This is exactly myth related, but it is such a knowledgeable community....
I just seem to have no luck with LIRC blasting. I have an HD-PVR and
initially setup HD-PVR to perform the blasting via lirc_zilog.
(Followed the procedure outlined in
http://www.mythtv.org/wiki/Hauppauge_HD-PVR#HD-PVR_Driver_Compilation_Howto).
Unfortunately, the HD-PVR would lockup after a while with the
lirc_zilog loaded. With the module unloaded, it seems fine. (Too
bad, because ir blasting and the remote seemed to work fine!)
I then tried to configure using serial port. I copied over the
lircd.conf file from the old server, setup hardware.conf and restarted
the service. The lirc_serial module seems to correctly load, but the
it doesn't change the channels. (Unfortunately this blaster doesn't
light up like the HD_PVR, so I can't see if a signal is actually being
sent, but if I plug it back into the old mythserver it still works..)
I found some notes suggesting there were some issues with serial
blasting in October and early January.
https://bugzilla.redhat.com/show_bug.cgi?id=658600
http://www.gossamer-threads.com/lists/mythtv/users/455608?do=post_view_threaded#455608
Im running MythBuntu 10.10, 2.6.35-28, and lircd 0.8.7-pre3. Any
suggestions on what to try next?
1) finding a combination of driver and lircd that works with hd-pvr
2) patching up lircd (not exactly sure how to do that now)
3) Wipe and install 10.4?
4) Gentoo? -- My old box is Gentoo, but MythBuntu just seems "easier"
at the time. :-)
I do remember when I built the old box years ago, that the major
version was important. I tried multiple combinations to get it to 61
on 10.10, but none worked so I gave up. I see others have 250 in the
web, so I'm assuming that is no longer an issue....
Thanks,
Greg.
ghormann@tvServer:/usr/local/bin$ dmesg | grep ttyS0
[ 0.970480] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.970721] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ghormann@tvServer:/usr/local/bin$ dmesg | grep lirc
[ 18.302736] lirc_dev: IR Remote Control driver registered, major 250
[ 18.389361] lirc_serial: module is from the staging directory, the
quality is unknown, you have been warned.
[ 19.346762] lirc_serial: auto-detected active high receiver
[ 19.346836] lirc_serial lirc_serial.0: lirc_dev: driver lirc_serial
registered at minor = 0
ghormann@tvServer:/usr/local/bin$ sudo modprobe -c | grep lirc
#alias char-major-61 lirc_dev
options lirc_serial irq=4 io=0x3f8
#options lirc_serial irq=3 io=0x2f8
ghormann@tvServer:/usr/local/bin$ lsmod | grep ir
lirc_serial 12654 0
lirc_dev 11209 1 lirc_serial
_______________________________________________
mythtv-users mailing list
mythtv-users@mythtv.org
http://www.mythtv.org/mailman/listinfo/mythtv-users
I just seem to have no luck with LIRC blasting. I have an HD-PVR and
initially setup HD-PVR to perform the blasting via lirc_zilog.
(Followed the procedure outlined in
http://www.mythtv.org/wiki/Hauppauge_HD-PVR#HD-PVR_Driver_Compilation_Howto).
Unfortunately, the HD-PVR would lockup after a while with the
lirc_zilog loaded. With the module unloaded, it seems fine. (Too
bad, because ir blasting and the remote seemed to work fine!)
I then tried to configure using serial port. I copied over the
lircd.conf file from the old server, setup hardware.conf and restarted
the service. The lirc_serial module seems to correctly load, but the
it doesn't change the channels. (Unfortunately this blaster doesn't
light up like the HD_PVR, so I can't see if a signal is actually being
sent, but if I plug it back into the old mythserver it still works..)
I found some notes suggesting there were some issues with serial
blasting in October and early January.
https://bugzilla.redhat.com/show_bug.cgi?id=658600
http://www.gossamer-threads.com/lists/mythtv/users/455608?do=post_view_threaded#455608
Im running MythBuntu 10.10, 2.6.35-28, and lircd 0.8.7-pre3. Any
suggestions on what to try next?
1) finding a combination of driver and lircd that works with hd-pvr
2) patching up lircd (not exactly sure how to do that now)
3) Wipe and install 10.4?
4) Gentoo? -- My old box is Gentoo, but MythBuntu just seems "easier"
at the time. :-)
I do remember when I built the old box years ago, that the major
version was important. I tried multiple combinations to get it to 61
on 10.10, but none worked so I gave up. I see others have 250 in the
web, so I'm assuming that is no longer an issue....
Thanks,
Greg.
ghormann@tvServer:/usr/local/bin$ dmesg | grep ttyS0
[ 0.970480] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.970721] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ghormann@tvServer:/usr/local/bin$ dmesg | grep lirc
[ 18.302736] lirc_dev: IR Remote Control driver registered, major 250
[ 18.389361] lirc_serial: module is from the staging directory, the
quality is unknown, you have been warned.
[ 19.346762] lirc_serial: auto-detected active high receiver
[ 19.346836] lirc_serial lirc_serial.0: lirc_dev: driver lirc_serial
registered at minor = 0
ghormann@tvServer:/usr/local/bin$ sudo modprobe -c | grep lirc
#alias char-major-61 lirc_dev
options lirc_serial irq=4 io=0x3f8
#options lirc_serial irq=3 io=0x2f8
ghormann@tvServer:/usr/local/bin$ lsmod | grep ir
lirc_serial 12654 0
lirc_dev 11209 1 lirc_serial
_______________________________________________
mythtv-users mailing list
mythtv-users@mythtv.org
http://www.mythtv.org/mailman/listinfo/mythtv-users