Hi all,
Could you please let me know PBR (Policy Based Routing) functionality
support is present in Quagga for both Static routes and Dynamic routing
cases or not.
I am able to see the configuration option to configure the route-map
config, but the next hop was not modified.
Below is my config for static case, Please correct me if I missed any
config.
Before applying the PBR config, route table info
K>* 0.0.0.0/0 via 10.200.8.1,vmmgmt
K>* 1.0.0.0/24 via 2.0.0.1, enp2s0f3
C>* 2.0.0.0/24 is directly connected, enp2s0f3
C>* 3.0.0.0/24 is directly connected, enp2s0f1
C>* 10.200.8.0/24 is directly connected, vmmgmt
S>* 25.25.0.0/24 [1/0] via 2.0.0.20, enp2s0f3
S>* 30.0.0.0/24 [1/0] via 3.0.0.40, enp2s0f1
Tried configuring PBR below two ways
1. Using access list
access-list anki permit 25.25.0.0/24
!
route-map qwe permit 5
match ip address anki
set ip next-hop 3.0.0.40
1. Directly applying matching ip
route-map aaa permit 2
match ip address 25.25.0.0/24
set ip next-hop 3.0.0.40
Note: I am not seeing any configuration support to apply the PBR config
under interface.
After applying the above config , show ip route in Quagga displays the same
output, next hop was not modified.
K>* 1.0.0.0/24 via 2.0.0.1, enp2s0f3
C>* 2.0.0.0/24 is directly connected, enp2s0f3
C>* 3.0.0.0/24 is directly connected, enp2s0f1
C>* 10.200.8.0/24 is directly connected, vmmgmt
S>* 25.25.0.0/24 [1/0] via 2.0.0.20, enp2s0f3
S>* 30.0.0.0/24 [1/0] via 3.0.0.40, enp2s0f1
C>* 127.0.0.0/8 is directly connected, lo
C>* 192.168.122.0/24 is directly connected, virbr0
Thanks a lot for your help in advance.
Thanks,
Anki
Could you please let me know PBR (Policy Based Routing) functionality
support is present in Quagga for both Static routes and Dynamic routing
cases or not.
I am able to see the configuration option to configure the route-map
config, but the next hop was not modified.
Below is my config for static case, Please correct me if I missed any
config.
Before applying the PBR config, route table info
K>* 0.0.0.0/0 via 10.200.8.1,vmmgmt
K>* 1.0.0.0/24 via 2.0.0.1, enp2s0f3
C>* 2.0.0.0/24 is directly connected, enp2s0f3
C>* 3.0.0.0/24 is directly connected, enp2s0f1
C>* 10.200.8.0/24 is directly connected, vmmgmt
S>* 25.25.0.0/24 [1/0] via 2.0.0.20, enp2s0f3
S>* 30.0.0.0/24 [1/0] via 3.0.0.40, enp2s0f1
Tried configuring PBR below two ways
1. Using access list
access-list anki permit 25.25.0.0/24
!
route-map qwe permit 5
match ip address anki
set ip next-hop 3.0.0.40
1. Directly applying matching ip
route-map aaa permit 2
match ip address 25.25.0.0/24
set ip next-hop 3.0.0.40
Note: I am not seeing any configuration support to apply the PBR config
under interface.
After applying the above config , show ip route in Quagga displays the same
output, next hop was not modified.
K>* 1.0.0.0/24 via 2.0.0.1, enp2s0f3
C>* 2.0.0.0/24 is directly connected, enp2s0f3
C>* 3.0.0.0/24 is directly connected, enp2s0f1
C>* 10.200.8.0/24 is directly connected, vmmgmt
S>* 25.25.0.0/24 [1/0] via 2.0.0.20, enp2s0f3
S>* 30.0.0.0/24 [1/0] via 3.0.0.40, enp2s0f1
C>* 127.0.0.0/8 is directly connected, lo
C>* 192.168.122.0/24 is directly connected, virbr0
Thanks a lot for your help in advance.
Thanks,
Anki