Mailing List Archive

On 9/17/2013 4:31 PM, Eldon Koyle wrote:
> Have you tried setting 'speed-duplex 100-full' on the interface?
>

Yep, no success:

SSH@router#speed-duplex 100-full
Error - can't change speed and duplex mode

-bill
_______________________________________________
foundry-nsp mailing list
foundry-nsp@puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp

Hi Bill,
I've posted the most recent copy of the supported optics info to my Dropbox account. You can use it to make sure the optic type, cable diameter, and code version all match.

https://dl.dropboxusercontent.com/u/3783334/External%20Brocade%20Qual%20and%20Support%20Transceiver%20Matrix%20%28061713%20All%20customers%20except%20HP%29%20v1.0.xls
https://dl.dropboxusercontent.com/u/3783334/Optics%20Family%20Data%20Sheet.pdf

It looks like we've supported this since v2.9 though, so I think your version is OK. You can confirm that the FPGA and IronWare images match on that card by running a "show mod" and "show ver". Compare the output of the LP with what is running on the MP; if something is mismatched you may also see an error message for the individual IronWare or FPGA (XPP) version inside the output.

If this is a 3rd party optic (non-brocade) you may need to disable the optics type checking with:

Brocade(config)# no transceiver-type-check

Hope this can get you working!

Wilbur


-----Original Message-----
From: foundry-nsp [mailto:foundry-nsp-bounces@puck.nether.net] On Behalf Of Bill
Sent: Tuesday, September 17, 2013 7:06 PM
To: foundry-nsp@puck.nether.net
Subject: [f-nsp] E1MG-100FX-IR-OM link not coming up on NI-XMR-1Gx20-SFP

I have some new brocade compatible optics (SFP) that we are trying to use for a customer that are not working.

E1MG-100FX-IR-OM is a 100FX (yes, 100 mbit) optic that is supposed to work in the NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module.

The manufacturer tells me that Brocade requires 3.9.0 code for these to work. Since the router is running 5.2.0d, maybe they are talking about FPGA code on the 1Gx20 card??

show media shows correct:

SSH@router#show media e 4/11
Port 4/11:
Type : SFP (LHA-1310nm)
Vendor: BROCADE , Version: 1.0
Part# : E1MG-100FX-IR-OM, Serial#: S1306014XXX
All show media done
SSH@router#show media e 4/12
Port 4/12:
Type : SFP (LHA-1310nm)
Vendor: BROCADE , Version: 1.0
Part# : E1MG-100FX-IR-OM, Serial#: S1306018XXX
All show media done

show optic shows correct:

SSH@router#show optic 4
Port Temperature Tx Power Rx Power Tx Bias Current
+----+-----------+-------------+------------+----------------+
4/11 39.6484 C -011.1294 dBm -011.1520 dBm 21.582 mA
Normal Normal Normal Normal
4/12 50.6210 C -009.8254 dBm -005.8787 dBm 24.198 mA
Normal Normal Normal Normal

With a loopback plug in the SFP, the port still shows down/down:

SSH@router#show int e 4/11
GigabitEthernet4/11 is down, line protocol is down
STP Root Guard is disabled, STP BPDU Guard is disabled
Hardware is GigabitEthernet, address is 000c.dbe8.4b9a (bia 000c.dbe8.4b9a)
Configured speed auto, actual unknown, configured duplex fdx, actual unknown
Member of VLAN 999 (untagged), port is in untagged mode, port state is Disabled
STP configured to ON, Priority is level0, flow control disabled
Priority force disabled, Drop precedence level 0, Drop precedence force disabled
dhcp-snooping-trust configured to OFF
mirror disabled, monitor disabled
LACP BPDU Forwarding:Disabled
Not member of any active trunks
Not member of any configured trunks
Port name is BILL TESTING 100FX OPTICS 8/27/2013
Internet address is 10.200.0.1/29, MTU 9200 bytes, encapsulation ethernet
Cluster L2 protocol forwarding enabled
300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
NP received 0 packets, Sent to TM 0 packets
NP Ingress dropped 0 packets
0 packets output, 0 bytes, 0 underruns
Transmitted 0 broadcasts, 0 multicasts, 0 unicasts
0 output errors, 0 collisions
NP transmitted 0 packets, Received from TM 0 packets

Port configuration:

SSH@router#sho run int e 4/11
interface ethernet 4/11
port-name BILL TESTING 100FX OPTICS 8/27/2013
enable
route-only
ip address 10.200.0.1/29
no flow-control

Router and firmware versions:

==========================================================================
SL 1: NI-XMR-10Gx4 4-port 10GbE Module (Serial #: PR1506XXXX, Part #:
31546-203A)
Boot : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade
Communications Systems, Inc.
Compiled on Jun 7 2011 at 17:06:54 labeled as xmlprm05200
(514997 bytes) from boot flash
Monitor : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade Communications Systems, Inc.
Compiled on Jun 7 2011 at 17:07:18 labeled as xmlb05200
(515819 bytes) from code flash
IronWare : Version 5.2.0dT177 Copyright (c) 1996-2009 Brocade Communications Systems, Inc.
Compiled on Mar 2 2012 at 19:00:00 labeled as xmlp05200d
(6529868 bytes) from Primary
FPGA versions:
Valid PBIF Version = 3.24, Build Time = 8/4/2010 16:29:00

Valid XPP Version = 6.23, Build Time = 2/4/2011 9:7:00

Valid XGMAC Version = 0.15, Build Time = 10/14/2010 16:31:00

X10G2MAC 0
X10G2MAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 0 Bytes BRAM
PPCR0: 0K entries CAM, 0K PRAM, 0K AGE RAM
PPCR1: 0K entries CAM, 0K PRAM, 0K AGE RAM LP Slot 1 uptime is 36 days 15 hours 1 minutes 18 seconds

==========================================================================
SL 4: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA1907XXXX, Part #: 35570-200B)
Boot : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade
Communications Systems, Inc.
Compiled on Jun 7 2011 at 17:06:54 labeled as xmlprm05200
(514997 bytes) from boot flash
Monitor : Version 5.2.0T175 Copyright (c) 1996-2009 Brocade Communications Systems, Inc.
Compiled on Jun 7 2011 at 17:07:18 labeled as xmlb05200
(515819 bytes) from code flash
IronWare : Version 5.2.0dT177 Copyright (c) 1996-2009 Brocade Communications Systems, Inc.
Compiled on Mar 2 2012 at 19:00:00 labeled as xmlp05200d
(6529868 bytes) from Primary
FPGA versions:
Valid PBIF Version = 3.24, Build Time = 8/4/2010 16:29:00

Valid XPP Version = 6.23, Build Time = 2/4/2011 9:7:00

BCM5695GMAC 0
BCM5695GMAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 0 Bytes BRAM
PPCR0: 0K entries CAM, 0K PRAM, 0K AGE RAM LP Slot 4 uptime is 36 days 15 hours 1 minutes 50 seconds ==========================================================================
_______________________________________________
foundry-nsp mailing list
foundry-nsp@puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________
foundry-nsp mailing list
foundry-nsp@puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp