Mailing List Archive

Replacing a SCSI cable
Hi,

what is the current recommendation as far as replacing a SCSI cable
connecting the filer and the tape library? Does filer need to be
rebooted, or is it safe to hot-swap the cable?

Thanks

Igor
RE: Replacing a SCSI cable [ In reply to ]
Igor,
You can hot swap the cable. I would sure no backup jobs are running
on the Netapp and if you are using NDMP make sure you turn it off (ndmpd
off) before swapping cables. It should work fine.
Mike


-----Original Message-----
From: Igor Schein [mailto:igor@txc.com]
Sent: Wednesday, October 09, 2002 6:05 PM
To: toasters@mathworks.com
Subject: Replacing a SCSI cable


Hi,

what is the current recommendation as far as replacing a SCSI cable
connecting the filer and the tape library? Does filer need to be
rebooted, or is it safe to hot-swap the cable?

Thanks

Igor
RE: Replacing a SCSI cable [ In reply to ]
Is that really safe? I was always taught never to connect or disconnect a
SCSI cable on a powered-up system due to the possibility of damaging the
SCSI controller, and I've actually seen that happen on a sparcstation once.
Do the netapps and the tape drives have some additional technology that
allows hot-swapping the scsi cable?

--
Mike Sphar - Sr Systems Administrator - Remedy Corporation

-----Original Message-----
From: Mike Ball [mailto:MBall@datalink.com]
Sent: Friday, October 11, 2002 7:36 AM
To: 'igor@txc.com'; toasters@mathworks.com
Subject: RE: Replacing a SCSI cable

Igor,
You can hot swap the cable. I would sure no backup jobs are running
on the Netapp and if you are using NDMP make sure you turn it off (ndmpd
off) before swapping cables. It should work fine.
Mike


-----Original Message-----
From: Igor Schein [mailto:igor@txc.com]
Sent: Wednesday, October 09, 2002 6:05 PM
To: toasters@mathworks.com
Subject: Replacing a SCSI cable


Hi,

what is the current recommendation as far as replacing a SCSI cable
connecting the filer and the tape library? Does filer need to be
rebooted, or is it safe to hot-swap the cable?

Thanks

Igor
RE: Replacing a SCSI cable [ In reply to ]
As long as there is no signal (ex- scanning SCSI card or Tape I/O) going
down the SCSI line while the cables are being swapped I have never had a
issue. It is nothing special about the Netapp.

-----Original Message-----
From: Mike Sphar [mailto:mike.sphar@Remedy.COM]
Sent: Friday, October 11, 2002 10:44 AM
To: toasters@mathworks.com
Subject: RE: Replacing a SCSI cable


Is that really safe? I was always taught never to connect or disconnect a
SCSI cable on a powered-up system due to the possibility of damaging the
SCSI controller, and I've actually seen that happen on a sparcstation once.
Do the netapps and the tape drives have some additional technology that
allows hot-swapping the scsi cable?

--
Mike Sphar - Sr Systems Administrator - Remedy Corporation

-----Original Message-----
From: Mike Ball [mailto:MBall@datalink.com]
Sent: Friday, October 11, 2002 7:36 AM
To: 'igor@txc.com'; toasters@mathworks.com
Subject: RE: Replacing a SCSI cable

Igor,
You can hot swap the cable. I would sure no backup jobs are running
on the Netapp and if you are using NDMP make sure you turn it off (ndmpd
off) before swapping cables. It should work fine.
Mike


-----Original Message-----
From: Igor Schein [mailto:igor@txc.com]
Sent: Wednesday, October 09, 2002 6:05 PM
To: toasters@mathworks.com
Subject: Replacing a SCSI cable


Hi,

what is the current recommendation as far as replacing a SCSI cable
connecting the filer and the tape library? Does filer need to be
rebooted, or is it safe to hot-swap the cable?

Thanks

Igor
RE: Replacing a SCSI cable [ In reply to ]
It's more or less "safe" if you are dealing with passive (differential)
interfaces. If dealing with active (single-ended) interface I like to be
sure that the device with the far end terminator is powered down. In any
case, all the devices in the string have to be idle when you break the
chain. SCSI controllers get most upset when they lose sight of their
terminator while a bus transaction is taking place.

Bill Link
SysAdmin, DSTOutput inc.
and Old Hardware Guy
bill_link@billing.com


-----Original Message-----
From: Mike Sphar [mailto:mike.sphar@Remedy.COM]
Sent: Friday, October 11, 2002 7:44 AM
To: toasters@mathworks.com
Subject: RE: Replacing a SCSI cable


Is that really safe? I was always taught never to connect or disconnect a
SCSI cable on a powered-up system due to the possibility of damaging the
SCSI controller, and I've actually seen that happen on a sparcstation once.
Do the netapps and the tape drives have some additional technology that
allows hot-swapping the scsi cable?

--
Mike Sphar - Sr Systems Administrator - Remedy Corporation

-----Original Message-----
From: Mike Ball [mailto:MBall@datalink.com]
Sent: Friday, October 11, 2002 7:36 AM
To: 'igor@txc.com'; toasters@mathworks.com
Subject: RE: Replacing a SCSI cable

Igor,
You can hot swap the cable. I would sure no backup jobs are running
on the Netapp and if you are using NDMP make sure you turn it off (ndmpd
off) before swapping cables. It should work fine.
Mike


-----Original Message-----
From: Igor Schein [mailto:igor@txc.com]
Sent: Wednesday, October 09, 2002 6:05 PM
To: toasters@mathworks.com
Subject: Replacing a SCSI cable


Hi,

what is the current recommendation as far as replacing a SCSI cable
connecting the filer and the tape library? Does filer need to be
rebooted, or is it safe to hot-swap the cable?

Thanks

Igor


Notice: This e-mail and any attachments are intended only for the individual
or company to which it is addressed and may contain information which is
privileged, confidential and prohibited from disclosure or unauthorized use
under applicable law. If you are not the intended recipient of this e-mail,
you are hereby notified that any use, dissemination, or copying of this
e-mail or the information contained in this e-mail is strictly prohibited by
the sender. If you have received this transmission in error, please return
the material received to the sender and delete all copies from your system.
Thank you.