Hi Andy,
I upgraded the BIOS on my motherboard today to deal with a problem I was
having with the USB ports. After the upgrade, a strange problem has emerged
with my second encoder card. Below is the output of my dmesg. I'm not sure
if this is something I can work around in software or not?
enc239-009-050:~# dmesg | grep cx18
cx18: Start initialization, version 1.0.4
cx18-0: Initializing card #0
cx18-0: Autodetected Hauppauge card
cx18 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
cx18-0: Unreasonably low latency timer, setting to 64 (was 32)
cx18-0: cx23418 revision 01010000 (B)
cx18-0: Autodetected Hauppauge HVR-1600
cx18-0: Raw VBI supported; Sliced VBI is not yet supported
tuner 1-0043: chip found @ 0x86 (cx18 i2c driver #0-1)
tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx18)
cx18-0: DVB Frontend registered
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB)
cx18-0: Registered device video32 for encoder YUV (16 x 128 kB)
cx18-0: Registered device vbi0 for encoder VBI (60 x 17328 bytes)
cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB)
cx18-0: Registered device radio0 for encoder radio
cx18-0: Initialized card #0: Hauppauge HVR-1600
cx18-1: Initializing card #1
cx18-1: Autodetected Hauppauge card
cx18 0000:00:0d.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
cx18-1: Unreasonably low latency timer, setting to 64 (was 32)
cx18-1: cx23418 revision 01010000 (B)
cx18-1: Autodetected Hauppauge HVR-1600
cx18-1: Raw VBI supported; Sliced VBI is not yet supported
tuner 3-0043: chip found @ 0x86 (cx18 i2c driver #1-1)
tuner 3-0061: chip found @ 0xc2 (cx18 i2c driver #1-1)
cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #1-0)
cx18-1: Registered device video1 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx18)
cx18-1: DVB Frontend registered
cx18-1: Registered DVB adapter1 for TS (32 x 32 kB)
cx18-1: Registered device video33 for encoder YUV (16 x 128 kB)
cx18-1: Registered device vbi1 for encoder VBI (60 x 17328 bytes)
cx18-1: Registered device video25 for encoder PCM audio (256 x 4 kB)
cx18-1: Registered device radio1 for encoder radio
cx18-1: Initialized card #1: Hauppauge HVR-1600
cx18: End initialization
cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
cx18-1: Retry loading firmware
cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
cx18-1: Failed to initialize on minor 5
cx18-1: FW version: 0.0.74.0 (Release 2007/03/12)
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
Any background on how to tackle this would be greatly appreciated.
enc239-009-050:~# cat /proc/interrupts
CPU0
0: 335058 IO-APIC-edge timer
1: 2 IO-APIC-edge i8042
9: 0 IO-APIC-fasteoi acpi
12: 4 IO-APIC-edge i8042
17: 97128 IO-APIC-fasteoi cx18-0
18: 122037 IO-APIC-fasteoi eth0, cx18-1
19: 707449 IO-APIC-fasteoi eth1
21: 276 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb2,
uhci_hcd:usb3, uhci_hcd:usb4
22: 0 IO-APIC-fasteoi VIA8237
NMI: 0 Non-maskable interrupts
LOC: 109 Local timer interrupts
TRM: 0 Thermal event interrupts
SPU: 0 Spurious interrupts
ERR: 0
MIS: 0
-Jeff
I upgraded the BIOS on my motherboard today to deal with a problem I was
having with the USB ports. After the upgrade, a strange problem has emerged
with my second encoder card. Below is the output of my dmesg. I'm not sure
if this is something I can work around in software or not?
enc239-009-050:~# dmesg | grep cx18
cx18: Start initialization, version 1.0.4
cx18-0: Initializing card #0
cx18-0: Autodetected Hauppauge card
cx18 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
cx18-0: Unreasonably low latency timer, setting to 64 (was 32)
cx18-0: cx23418 revision 01010000 (B)
cx18-0: Autodetected Hauppauge HVR-1600
cx18-0: Raw VBI supported; Sliced VBI is not yet supported
tuner 1-0043: chip found @ 0x86 (cx18 i2c driver #0-1)
tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx18)
cx18-0: DVB Frontend registered
cx18-0: Registered DVB adapter0 for TS (32 x 32 kB)
cx18-0: Registered device video32 for encoder YUV (16 x 128 kB)
cx18-0: Registered device vbi0 for encoder VBI (60 x 17328 bytes)
cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB)
cx18-0: Registered device radio0 for encoder radio
cx18-0: Initialized card #0: Hauppauge HVR-1600
cx18-1: Initializing card #1
cx18-1: Autodetected Hauppauge card
cx18 0000:00:0d.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
cx18-1: Unreasonably low latency timer, setting to 64 (was 32)
cx18-1: cx23418 revision 01010000 (B)
cx18-1: Autodetected Hauppauge HVR-1600
cx18-1: Raw VBI supported; Sliced VBI is not yet supported
tuner 3-0043: chip found @ 0x86 (cx18 i2c driver #1-1)
tuner 3-0061: chip found @ 0xc2 (cx18 i2c driver #1-1)
cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #1-0)
cx18-1: Registered device video1 for encoder MPEG (64 x 32 kB)
DVB: registering new adapter (cx18)
cx18-1: DVB Frontend registered
cx18-1: Registered DVB adapter1 for TS (32 x 32 kB)
cx18-1: Registered device video33 for encoder YUV (16 x 128 kB)
cx18-1: Registered device vbi1 for encoder VBI (60 x 17328 bytes)
cx18-1: Registered device video25 for encoder PCM audio (256 x 4 kB)
cx18-1: Registered device radio1 for encoder radio
cx18-1: Initialized card #1: Hauppauge HVR-1600
cx18: End initialization
cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
cx18-1: Retry loading firmware
cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
cx18-1: Failed to initialize on minor 5
cx18-1: FW version: 0.0.74.0 (Release 2007/03/12)
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
cx18-1: Failed to initialize on minor 5
Any background on how to tackle this would be greatly appreciated.
enc239-009-050:~# cat /proc/interrupts
CPU0
0: 335058 IO-APIC-edge timer
1: 2 IO-APIC-edge i8042
9: 0 IO-APIC-fasteoi acpi
12: 4 IO-APIC-edge i8042
17: 97128 IO-APIC-fasteoi cx18-0
18: 122037 IO-APIC-fasteoi eth0, cx18-1
19: 707449 IO-APIC-fasteoi eth1
21: 276 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb2,
uhci_hcd:usb3, uhci_hcd:usb4
22: 0 IO-APIC-fasteoi VIA8237
NMI: 0 Non-maskable interrupts
LOC: 109 Local timer interrupts
TRM: 0 Thermal event interrupts
SPU: 0 Spurious interrupts
ERR: 0
MIS: 0
-Jeff