Mailing List Archive: [UNKNOWN IVTV CARD] ? pvr-500 not working after kernel upgrade

[UNKNOWN IVTV CARD] ? pvr-500 not working after kernel upgrade

Dec 19, 2008, 1:51 AM

Post #1 of 3 (2872 views)

old kernel 2.5.25:

ivtv: Start initialization, version 1.2.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 17 (level, low) -> IRQ 17
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 1-0050: Hauppauge model 23559, rev D591, serial# 8228089
tveeprom 1-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
(eeprom 0x74)
tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR receiver, has no IR transmitter
ivtv0: Autodetected WinTV PVR 500 (unit #1)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tea5767 1-0060: type set to Philips TEA5767HN FM Radio
tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 1-0043: tda988[5/6/7] found
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
tuner-simple 1-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME
MK4))
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Initialized card #0: WinTV PVR 500 (unit #1)
ivtv1: Initializing card #1
ivtv1: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 18
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 2-0050: Hauppauge model 23559, rev D591, serial# 8228089
tveeprom 2-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56)
tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
(eeprom 0x74)
tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR receiver, has no IR transmitter
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: Autodetected WinTV PVR 500 (unit #2)
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #1)
tda9887 2-0043: tda988[5/6/7] found
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
tuner-simple 2-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME
MK4))
cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
ivtv1: Registered device video1 for encoder MPG (4096 kB)
ivtv1: Registered device video33 for encoder YUV (2048 kB)
ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
ivtv1: Registered device video25 for encoder PCM (320 kB)
ivtv1: Initialized card #1: WinTV PVR 500 (unit #2)
ivtv: End initialization

some git commands
make oldconfig
lots of enters
new kernel 2.6.27.10:

ivtv: Start initialization, version 1.4.0
ivtv0: Initializing card #0
ivtv0: Unknown card: vendor/device: 4444/0016
ivtv0: subsystem vendor/device: ffff/ffff
ivtv0: cx23416 based
ivtv0: Defaulting to Hauppauge WinTV PVR-150 card
ivtv0: Please mail the vendor/device and subsystem vendor/device IDs and
what kind of
ivtv0: card you have to the ivtv-devel mailinglist (www.ivtvdriver.org)
ivtv0: Prefix your subject line with [UNKNOWN IVTV CARD].
ivtv0: Cannot request encoder memory region on card 0.
ivtv0: Error -5 on initialization
ivtv: probe of 0000:02:09.0 failed with error -5
ivtv: End initialization

Somehow I do not be leave the 'Unknown card'

--
Hans

_______________________________________________
ivtv-devel mailing list
ivtv-devel@ivtvdriver.org
http://ivtvdriver.org/mailman/listinfo/ivtv-devel

Re: [UNKNOWN IVTV CARD] ? pvr-500 not working after kernel upgrade [ In reply to ]

awalls at radix

Dec 19, 2008, 3:32 AM

Post #2 of 3 (2605 views)

Permalink

On Fri, 2008-12-19 at 10:51 +0100, Hans de Bruin wrote:
>
> old kernel 2.5.25:
>
> ivtv: Start initialization, version 1.2.0
> ivtv0: Initializing card #0
> ivtv0: Autodetected Hauppauge card (cx23416 based)
> ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 17 (level, low) -> IRQ 17
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom 1-0050: Hauppauge model 23559, rev D591, serial# 8228089
> tveeprom 1-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56)
> tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
> (eeprom 0x74)
> tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio (idx
> 101, type 62)
> tveeprom 1-0050: audio processor is CX25843 (idx 37)
> tveeprom 1-0050: decoder processor is CX25843 (idx 30)
> tveeprom 1-0050: has radio, has no IR receiver, has no IR transmitter
> ivtv0: Autodetected WinTV PVR 500 (unit #1)
> cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
> tea5767 1-0060: type set to Philips TEA5767HN FM Radio
> tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
> tda9887 1-0043: tda988[5/6/7] found
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
> tuner-simple 1-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME
> MK4))
> cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> ivtv0: Registered device video0 for encoder MPG (4096 kB)
> ivtv0: Registered device video32 for encoder YUV (2048 kB)
> ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
> ivtv0: Registered device video24 for encoder PCM (320 kB)
> ivtv0: Registered device radio0 for encoder radio
> ivtv0: Initialized card #0: WinTV PVR 500 (unit #1)
> ivtv1: Initializing card #1
> ivtv1: Autodetected Hauppauge card (cx23416 based)
> ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 18
> ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom 2-0050: Hauppauge model 23559, rev D591, serial# 8228089
> tveeprom 2-0050: tuner model is Philips FQ1216AME MK4 (idx 91, type 56)
> tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
> (eeprom 0x74)
> tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx
> 101, type 62)
> tveeprom 2-0050: audio processor is CX25843 (idx 37)
> tveeprom 2-0050: decoder processor is CX25843 (idx 30)
> tveeprom 2-0050: has radio, has no IR receiver, has no IR transmitter
> ivtv1: Correcting tveeprom data: no radio present on second unit
> ivtv1: Autodetected WinTV PVR 500 (unit #2)
> cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> tuner 2-0043: chip found @ 0x86 (ivtv i2c driver #1)
> tda9887 2-0043: tda988[5/6/7] found
> tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
> tuner-simple 2-0061: type set to 56 (Philips PAL/SECAM multi (FQ1216AME
> MK4))
> cx25840 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> ivtv1: Registered device video1 for encoder MPG (4096 kB)
> ivtv1: Registered device video33 for encoder YUV (2048 kB)
> ivtv1: Registered device vbi1 for encoder VBI (1024 kB)
> ivtv1: Registered device video25 for encoder PCM (320 kB)
> ivtv1: Initialized card #1: WinTV PVR 500 (unit #2)
> ivtv: End initialization
>
> some git commands
> make oldconfig
> lots of enters
> new kernel 2.6.27.10:
>
> ivtv: Start initialization, version 1.4.0
> ivtv0: Initializing card #0
> ivtv0: Unknown card: vendor/device: 4444/0016
> ivtv0: subsystem vendor/device: ffff/ffff

PCI bus errors return 0xffffffff. A new kernel and drivers with a
busier, more I/O intensive boot sequence may be triggering it.

1. Make sure lspci -vnn shows real numbers and not ff's.

2. Unload and reload ivtv module.

If that doesn't help, try removing the card, blowing out any dust and
reinstalling the card.

Regards,
Andy

> ivtv0: cx23416 based
> ivtv0: Defaulting to Hauppauge WinTV PVR-150 card
> ivtv0: Please mail the vendor/device and subsystem vendor/device IDs and
> what kind of
> ivtv0: card you have to the ivtv-devel mailinglist (www.ivtvdriver.org)
> ivtv0: Prefix your subject line with [UNKNOWN IVTV CARD].
> ivtv0: Cannot request encoder memory region on card 0.
> ivtv0: Error -5 on initialization
> ivtv: probe of 0000:02:09.0 failed with error -5
> ivtv: End initialization
>
>
> Somehow I do not be leave the 'Unknown card'
>

_______________________________________________
ivtv-devel mailing list
ivtv-devel@ivtvdriver.org
http://ivtvdriver.org/mailman/listinfo/ivtv-devel

Re: [UNKNOWN IVTV CARD] ? pvr-500 not working after kernel upgrade [ In reply to ]

bruinjm at xs4all

Dec 19, 2008, 5:34 AM

Post #3 of 3 (2621 views)

Permalink

Andy Walls wrote:
> On Fri, 2008-12-19 at 10:51 +0100, Hans de Bruin wrote:
>> old kernel 2.5.25:
>>
...

>> ivtv0: Unknown card: vendor/device: 4444/0016
>> ivtv0: subsystem vendor/device: ffff/ffff
>
> PCI bus errors return 0xffffffff. A new kernel and drivers with a
> busier, more I/O intensive boot sequence may be triggering it.
>
> 1. Make sure lspci -vnn shows real numbers and not ff's.
>
> 2. Unload and reload ivtv module.
>
>
> If that doesn't help, try removing the card, blowing out any dust and
> reinstalling the card.

lspci hung up my server immediately, so I blew out the dust and
reinstalled the card and de memory. Apparently 2.6.25 was more dust
proof. The pvr500 is now up and running, but there is a minor nuisance .
After a cold boot I have to rmmod ivtv;modprobe ivtv to get a picture
instead of just noise. After this a warm boot just works fine.

--
Hans

_______________________________________________
ivtv-devel mailing list
ivtv-devel@ivtvdriver.org
http://ivtvdriver.org/mailman/listinfo/ivtv-devel