Hi!
I have just installed gentoo on my ibook 12". It has dual boot with
yaboot. Sometimes it works fine but sometimes, without any reason it
starts as follows and stop:
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Thermal assist unit not available
Registering PowerMac CPU frequency driver
Low: 599 Mhz, High: 1199 Mhz, Boot: 599 Mhz
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.22 [Flags: R/W].
inotify device minor=63
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 Mhz (RefDiv=12) Memory=190.00 Mhz, System=183.00
Mhz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Console: switching to colour frame buffer device 128x48
Registered "mnca" backlight controller, level: 15/15
radeonfb: ATI Radeon \c DDR SGRAM 32 MB
i8042.c: i8042 controller self test timeout.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
At this point it stops and nothing happens.... if I try to restart the
machine it usually works, but ssometimes I need to restart it more than
once.
Does anyone know what is the problem?
Best regards,
Flavio Leonardo Cavalcanti de Moura
email: flavio@mat.unb.br
homepage: flavio.mat.unb.br
--
gentoo-ppc-user@gentoo.org mailing list
I have just installed gentoo on my ibook 12". It has dual boot with
yaboot. Sometimes it works fine but sometimes, without any reason it
starts as follows and stop:
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:10:18.0
PCI: Cannot allocate resource region 0 of device 0001:10:19.0
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Thermal assist unit not available
Registering PowerMac CPU frequency driver
Low: 599 Mhz, High: 1199 Mhz, Boot: 599 Mhz
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.22 [Flags: R/W].
inotify device minor=63
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retrieved PLL infos from Open Firmware
radeonfb: Reference=27.00 Mhz (RefDiv=12) Memory=190.00 Mhz, System=183.00
Mhz
radeonfb: PLL min 12000 max 35000
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Console: switching to colour frame buffer device 128x48
Registered "mnca" backlight controller, level: 15/15
radeonfb: ATI Radeon \c DDR SGRAM 32 MB
i8042.c: i8042 controller self test timeout.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
At this point it stops and nothing happens.... if I try to restart the
machine it usually works, but ssometimes I need to restart it more than
once.
Does anyone know what is the problem?
Best regards,
Flavio Leonardo Cavalcanti de Moura
email: flavio@mat.unb.br
homepage: flavio.mat.unb.br
--
gentoo-ppc-user@gentoo.org mailing list