Hi,
I've tested live cd 2005.0-r4 and after a few lines of kernel
messages the display became black. The last line I saw was something
with "smp_cXX". But the system was still alive because I was able to
bring up ethernet and sshd by typing sightlessly. It's an iMac G5 1.8
GHz from october 2004
Found initrd at 0xc000000001d00000:0xc000000001de8c0a
trying to initialize btext ...
U3-DART: table not allocated, using direct DMA
Starting Linux PPC64 2.6.12-gentoo-livecd
-----------------------------------------------------
ppc64_pft_size = 0x18
ppc64_debug_switch = 0x0
ppc64_interrupt_controller = 0x1
systemcfg = 0xc000000000554000
systemcfg->platform = 0x400
systemcfg->processorCount = 0x1
systemcfg->physicalMemorySize = 0x30000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0xc00000002e000000
htab_hash_mask = 0x1ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.12-gentoo-livecd (root@G5) (gcc version 3.4.3
20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #1 SMP Thu
Jun 23 11:23:27 UTC 2005
[boot]0012 Setup Arch
Syscall map setup, 229 32 bits and 205 64 bits syscalls
Found U3 memory controller & host bridge, revision: 57
Mapped at 0xe000000080152000
Found a K2 mac-io controller, rev: 0, mapped at 0xe000000080193000
PowerMac motherboard: iMac G5
nvram: Checking bank 0...
nvram: gen0=52, gen1=51
nvram: Active bank is: 0
Adding PCI host bridge /pci@0,f0000000
Found U3-AGP PCI host bridge. Firmware bus number: 240->255
Adding PCI host bridge /ht@0,f2000000
Can't get bus-range for /ht@0,f2000000, assume bus 0
U3/HT: hole, 0 end at 8fffffff, 1 start at b0000000
Found U3-HT PCI host bridge. Firmware bus number: 0->239
Can't get bus-range for /ht@0,f2000000
PCI Host 0, io start: fffffffffd800000; io end: fffffffffdffffff
PCI Host 1, io start: 0; io end: 3fffff
Using native/NAP idle loop
Top of RAM: 0x30000000, Total RAM: 0x30000000
Memory hole size: 0MB
On node 0 totalpages: 196608
DMA zone: 196608 pages, LIFO batch:31
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/ram rw ramdisk_size=11000 cdroot devfs
init=/linuxrc
PowerMac using OpenPIC irq controller at 0x80040000
mpic: Setting up MPIC " K2-MPIC " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
Slave OpenPIC at 0xf8040000 hooked on IRQ 96
mpic: Setting up MPIC " U3-MPIC " version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 33.333333 MHz
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 46 => 0 (71)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 748156k/786432k available (4388k kernel code, 37552k
reserved, 1664k data, 442k bss, 340k init)
Calibrating delay loop... 66.30 BogoMIPS (lpj=33152)
Mount-cache hash table entries: 256
PowerMac SMP probe found 1 cpus
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 1
groups: 1
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Freeing initrd memory: 931k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Probing PCI hardware done
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
i/pSeries Real Time Clock Driver v1.1
nvram_init: Could not find nvram partition for nvram buffered error
logging.
Total HugeTLB memory allocated, 0
inotify device minor=63
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFS: nTxBlock = 5857, nTxLock = 46863
Initializing Cryptographic API
rivafb: nVidia device/chipset 10DE0329
rivafb: nVidia Corporation NV34M [GeForce FX Go5200]
rivafb: On a laptop. Assuming Digital Flat Panel
rivafb: Detected CRTC controller 1 being used
rivafb: disabling acceleration
rivafb: setting virtual Y resolution to 46603
Console: switching to colour frame buffer device 180x56
rivafb: PCI nVidia NV32 framebuffer ver 0.9.5b (64MB @ 0xA0000000)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 11000K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2
Copyright (c) 1999-2004 Intel Corporation.
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
PHY ID: 4061e4, addr: 0
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:59:84:b4
eth0: Found BCM5221 PHY
MacIO PCI driver attached to K2 chipset
Warning: no ADB interface detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PCI: Enabling device: (0001:02:0d.0), cmd 2
ide0: Found Apple Shasta ATA-6 controller, bus ID 3, irq 38
Probing IDE interface ide0...
hda: MATSHITADVD-R UJ-825, ATAPI CD/DVD-ROM drive
hda: Enabling Ultra DMA 4
ide0 at 0xe00000008802c000-0xe00000008802c007,0xe00000008802c160 on
irq 38
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
libata version 1.11 loaded.
sata_svw version 1.05
ata1: SATA max UDMA/133 cmd 0xE00000008802E000 ctl 0xE00000008802E020
bmdma 0xE00000008802E030 irq 10
ata2: SATA max UDMA/133 cmd 0xE00000008802E100 ctl 0xE00000008802E120
bmdma 0xE00000008802E130 irq 10
ata3: SATA max UDMA/133 cmd 0xE00000008802E200 ctl 0xE00000008802E220
bmdma 0xE00000008802E230 irq 10
ata4: SATA max UDMA/133 cmd 0xE00000008802E300 ctl 0xE00000008802E320
bmdma 0xE00000008802E330 irq 10
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01
87:4003 88:007f
ata1: dev 0 ATA, max UDMA/133, 156301488 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_svw
ata2: no device found (phy stat 00000004)
scsi1 : sata_svw
ata3: no device found (phy stat 00000000)
scsi2 : sata_svw
ata4: no device found (phy stat 00000000)
scsi3 : sata_svw
Vendor: ATA Model: ST380013AS Rev: 5.06
Type: Direct-Access ANSI SCSI revision: 05
st: Version 20050312, fixed bufsize 32768, s/g segs 256
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8 p9
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device: (0001:02:0e.0), cmd 2
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[39] MMIO=
[80100000-801007ff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugs is not available
PCI: Enabling device: (0001:01:0b.2), cmd 6
ehci_hcd 0001:01:0b.2: NEC Corporation USB 2.0
ehci_hcd 0001:01:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:01:0b.2: irq 70, io mem 0x80080000
ehci_hcd 0001:01:0b.2: park 0
ehci_hcd 0001:01:0b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device: (0001:01:0b.0), cmd 2
ohci_hcd 0001:01:0b.0: NEC Corporation USB
ohci_hcd 0001:01:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:0b.0: irq 70, io mem 0x80082000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device: (0001:01:0b.1), cmd 2
ohci_hcd 0001:01:0b.1: NEC Corporation USB (#2)
ohci_hcd 0001:01:0b.1: new USB bus registered, assigned bus number 3
ohci_hcd 0001:01:0b.1: irq 70, io mem 0x80081000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ohci_hcd and address 2
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d93fffe5984b4]
usb 3-1: new low speed USB device using ohci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with
IntelliEye(TM)] on usb-0001:01:0b.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Found KeyWest i2c on "u3", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2032.000 MB/sec
8regs_prefetch: 1644.000 MB/sec
32regs : 2372.000 MB/sec
32regs_prefetch: 1984.000 MB/sec
raid5: using function: 32regs (2372.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
oprofile: using ppc64/970 performance monitoring.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
IPv4 over IPv4 tunneling driver
ip_conntrack version 2.1 (3072 buckets, 24576 max) - 304 bytes per
conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://
snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
usb 2-1.2: new full speed USB device using ohci_hcd and address 3
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 340k freed
usb 2-1.3: new full speed USB device using ohci_hcd and address 4
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB
Keyboard] on usb-0001:01:0b.0-1.3
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB
Keyboard] on usb-0001:01:0b.0-1.3
VFS: Can't find ext3 filesystem on dev hda.
VFS: Can't find an ext2 filesystem on dev hda.
cramfs: wrong magic
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 18 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 18 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 8e len=1 81 => -1 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
usb 1-3: new high speed USB device using ehci_hcd and address 4
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sdb: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have
changed
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
/dev/scsi/host4/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi4, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
VFS: Can't find ext3 filesystem on dev sda1.
usb 1-3: USB disconnect, address 4
usb 1-3: new high speed USB device using ehci_hcd and address 5
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sdb: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have
changed
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
/dev/scsi/host5/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi5, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
VFS: Can't find ext3 filesystem on dev sda1.
0000:f0:0b.0 Host bridge: Apple Computer Inc. U3L AGP Bridge
Flags: bus master, 66Mhz, medium devsel, latency 16
Capabilities: [80] AGP version 3.0
0000:f0:10.0 VGA compatible controller: nVidia Corporation NV34M
[GeForce FX Go5200] (rev a1) (prog-if 00 [VGA])
Subsystem: nVidia Corporation: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 59
Memory at 91000000 (32-bit, non-prefetchable) [size=90000000]
Memory at a0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at 00020000 [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0
0001:00:01.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: 80200000-805fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [0061]
Capabilities: [90] #08 [8000]
0001:00:02.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [8824]
0001:00:03.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [8824]
0001:01:01.0 Network controller: Broadcom Corporation BCM4306 802.11b/
g Wireless LAN Controller (rev 03)
Subsystem: Apple Computer Inc.: Unknown device 004e
Flags: bus master, fast devsel, latency 16, IRQ 60
Memory at 80084000 (32-bit, non-prefetchable) [disabled]
Capabilities: [40] Power Management version 2
0001:01:07.0 Class ff00: Apple Computer Inc. Shasta Mac I/O
Flags: bus master, medium devsel, latency 16
Memory at 80000000 (32-bit, non-prefetchable)
0001:01:0b.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10
[OHCI])
Subsystem: NEC Corporation USB
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80082000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:01:0b.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10
[OHCI])
Subsystem: NEC Corporation USB
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80081000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:01:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-
if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80080000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:02:0c.0 IDE interface: Broadcom (formerly ServerWorks) K2 SATA
(prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Broadcom (formerly ServerWorks) K2 SATA
Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 10
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
Memory at 80102000 (32-bit, non-prefetchable) [size=8K]
0001:02:0d.0 Class ff00: Apple Computer Inc. Shasta IDE
Flags: bus master, medium devsel, latency 32, IRQ 38
Memory at 80104000 (32-bit, non-prefetchable)
0001:02:0e.0 FireWire (IEEE 1394): Apple Computer Inc. Shasta
Firewire (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc.: Unknown device 5811
Flags: bus master, medium devsel, latency 248, IRQ 39
Memory at 80100000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
0001:03:0f.0 Ethernet controller: Apple Computer Inc. Shasta (Sun GEM)
Flags: bus master, 66Mhz, slow devsel, latency 16, IRQ 40
Memory at 80400000 (32-bit, non-prefetchable) [size=80200000]
Expansion ROM at 00100000 [disabled]
I've tested live cd 2005.0-r4 and after a few lines of kernel
messages the display became black. The last line I saw was something
with "smp_cXX". But the system was still alive because I was able to
bring up ethernet and sshd by typing sightlessly. It's an iMac G5 1.8
GHz from october 2004
Found initrd at 0xc000000001d00000:0xc000000001de8c0a
trying to initialize btext ...
U3-DART: table not allocated, using direct DMA
Starting Linux PPC64 2.6.12-gentoo-livecd
-----------------------------------------------------
ppc64_pft_size = 0x18
ppc64_debug_switch = 0x0
ppc64_interrupt_controller = 0x1
systemcfg = 0xc000000000554000
systemcfg->platform = 0x400
systemcfg->processorCount = 0x1
systemcfg->physicalMemorySize = 0x30000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0xc00000002e000000
htab_hash_mask = 0x1ffff
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
Linux version 2.6.12-gentoo-livecd (root@G5) (gcc version 3.4.3
20041125 (Gentoo Linux 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #1 SMP Thu
Jun 23 11:23:27 UTC 2005
[boot]0012 Setup Arch
Syscall map setup, 229 32 bits and 205 64 bits syscalls
Found U3 memory controller & host bridge, revision: 57
Mapped at 0xe000000080152000
Found a K2 mac-io controller, rev: 0, mapped at 0xe000000080193000
PowerMac motherboard: iMac G5
nvram: Checking bank 0...
nvram: gen0=52, gen1=51
nvram: Active bank is: 0
Adding PCI host bridge /pci@0,f0000000
Found U3-AGP PCI host bridge. Firmware bus number: 240->255
Adding PCI host bridge /ht@0,f2000000
Can't get bus-range for /ht@0,f2000000, assume bus 0
U3/HT: hole, 0 end at 8fffffff, 1 start at b0000000
Found U3-HT PCI host bridge. Firmware bus number: 0->239
Can't get bus-range for /ht@0,f2000000
PCI Host 0, io start: fffffffffd800000; io end: fffffffffdffffff
PCI Host 1, io start: 0; io end: 3fffff
Using native/NAP idle loop
Top of RAM: 0x30000000, Total RAM: 0x30000000
Memory hole size: 0MB
On node 0 totalpages: 196608
DMA zone: 196608 pages, LIFO batch:31
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: root=/dev/ram rw ramdisk_size=11000 cdroot devfs
init=/linuxrc
PowerMac using OpenPIC irq controller at 0x80040000
mpic: Setting up MPIC " K2-MPIC " version 1.2 at 80040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
Slave OpenPIC at 0xf8040000 hooked on IRQ 96
mpic: Setting up MPIC " U3-MPIC " version 1.2 at f8040000, max 4 CPUs
mpic: ISU size: 124, shift: 7, mask: 7f
mpic: Initializing for 124 sources
PID hash table entries: 4096 (order: 12, 131072 bytes)
time_init: decrementer frequency = 33.333333 MHz
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 46 => 0 (71)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 748156k/786432k available (4388k kernel code, 37552k
reserved, 1664k data, 442k bss, 340k init)
Calibrating delay loop... 66.30 BogoMIPS (lpj=33152)
Mount-cache hash table entries: 256
PowerMac SMP probe found 1 cpus
Brought up 1 CPUs
CPU0 attaching sched-domain:
domain 0: span 1
groups: 1
checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
Freeing initrd memory: 931k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Probing PCI hardware done
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
i/pSeries Real Time Clock Driver v1.1
nvram_init: Could not find nvram partition for nvram buffered error
logging.
Total HugeTLB memory allocated, 0
inotify device minor=63
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFS: nTxBlock = 5857, nTxLock = 46863
Initializing Cryptographic API
rivafb: nVidia device/chipset 10DE0329
rivafb: nVidia Corporation NV34M [GeForce FX Go5200]
rivafb: On a laptop. Assuming Digital Flat Panel
rivafb: Detected CRTC controller 1 being used
rivafb: disabling acceleration
rivafb: setting virtual Y resolution to 46603
Console: switching to colour frame buffer device 180x56
rivafb: PCI nVidia NV32 framebuffer ver 0.9.5b (64MB @ 0xA0000000)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 11000K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2
Copyright (c) 1999-2004 Intel Corporation.
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
PHY ID: 4061e4, addr: 0
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:59:84:b4
eth0: Found BCM5221 PHY
MacIO PCI driver attached to K2 chipset
Warning: no ADB interface detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PCI: Enabling device: (0001:02:0d.0), cmd 2
ide0: Found Apple Shasta ATA-6 controller, bus ID 3, irq 38
Probing IDE interface ide0...
hda: MATSHITADVD-R UJ-825, ATAPI CD/DVD-ROM drive
hda: Enabling Ultra DMA 4
ide0 at 0xe00000008802c000-0xe00000008802c007,0xe00000008802c160 on
irq 38
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
libata version 1.11 loaded.
sata_svw version 1.05
ata1: SATA max UDMA/133 cmd 0xE00000008802E000 ctl 0xE00000008802E020
bmdma 0xE00000008802E030 irq 10
ata2: SATA max UDMA/133 cmd 0xE00000008802E100 ctl 0xE00000008802E120
bmdma 0xE00000008802E130 irq 10
ata3: SATA max UDMA/133 cmd 0xE00000008802E200 ctl 0xE00000008802E220
bmdma 0xE00000008802E230 irq 10
ata4: SATA max UDMA/133 cmd 0xE00000008802E300 ctl 0xE00000008802E320
bmdma 0xE00000008802E330 irq 10
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01
87:4003 88:007f
ata1: dev 0 ATA, max UDMA/133, 156301488 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_svw
ata2: no device found (phy stat 00000004)
scsi1 : sata_svw
ata3: no device found (phy stat 00000000)
scsi2 : sata_svw
ata4: no device found (phy stat 00000000)
scsi3 : sata_svw
Vendor: ATA Model: ST380013AS Rev: 5.06
Type: Direct-Access ANSI SCSI revision: 05
st: Version 20050312, fixed bufsize 32768, s/g segs 256
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8 p9
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device: (0001:02:0e.0), cmd 2
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[39] MMIO=
[80100000-801007ff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugs is not available
PCI: Enabling device: (0001:01:0b.2), cmd 6
ehci_hcd 0001:01:0b.2: NEC Corporation USB 2.0
ehci_hcd 0001:01:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:01:0b.2: irq 70, io mem 0x80080000
ehci_hcd 0001:01:0b.2: park 0
ehci_hcd 0001:01:0b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec
2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device: (0001:01:0b.0), cmd 2
ohci_hcd 0001:01:0b.0: NEC Corporation USB
ohci_hcd 0001:01:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:0b.0: irq 70, io mem 0x80082000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device: (0001:01:0b.1), cmd 2
ohci_hcd 0001:01:0b.1: NEC Corporation USB (#2)
ohci_hcd 0001:01:0b.1: new USB bus registered, assigned bus number 3
ohci_hcd 0001:01:0b.1: irq 70, io mem 0x80081000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb 2-1: new full speed USB device using ohci_hcd and address 2
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d93fffe5984b4]
usb 3-1: new low speed USB device using ohci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with
IntelliEye(TM)] on usb-0001:01:0b.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Found KeyWest i2c on "u3", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2032.000 MB/sec
8regs_prefetch: 1644.000 MB/sec
32regs : 2372.000 MB/sec
32regs_prefetch: 1984.000 MB/sec
raid5: using function: 32regs (2372.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
oprofile: using ppc64/970 performance monitoring.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
IPv4 over IPv4 tunneling driver
ip_conntrack version 2.1 (3072 buckets, 24576 max) - 304 bytes per
conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://
snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
usb 2-1.2: new full speed USB device using ohci_hcd and address 3
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 340k freed
usb 2-1.3: new full speed USB device using ohci_hcd and address 4
input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB
Keyboard] on usb-0001:01:0b.0-1.3
input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB
Keyboard] on usb-0001:01:0b.0-1.3
VFS: Can't find ext3 filesystem on dev hda.
VFS: Can't find an ext2 filesystem on dev hda.
cramfs: wrong magic
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 18 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 18 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 8e len=1 81 => -1 (71)
SMU do_cmd 8e len=1 81
SMU do_cmd 71 len=7 19 => 0 (71)
usb 1-3: new high speed USB device using ehci_hcd and address 4
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sdb: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have
changed
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
/dev/scsi/host4/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi4, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
VFS: Can't find ext3 filesystem on dev sda1.
usb 1-3: USB disconnect, address 4
usb 1-3: new high speed USB device using ehci_hcd and address 5
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Mobile Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sdb: Unit Not Ready, sense:
: Current: sense key: Unit Attention
Additional sense: Not ready to ready change, medium may have
changed
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
/dev/scsi/host5/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi5, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi5, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
VFS: Can't find ext3 filesystem on dev sda1.
0000:f0:0b.0 Host bridge: Apple Computer Inc. U3L AGP Bridge
Flags: bus master, 66Mhz, medium devsel, latency 16
Capabilities: [80] AGP version 3.0
0000:f0:10.0 VGA compatible controller: nVidia Corporation NV34M
[GeForce FX Go5200] (rev a1) (prog-if 00 [VGA])
Subsystem: nVidia Corporation: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 59
Memory at 91000000 (32-bit, non-prefetchable) [size=90000000]
Memory at a0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at 00020000 [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0
0001:00:01.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: 80200000-805fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [0061]
Capabilities: [90] #08 [8000]
0001:00:02.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [8824]
0001:00:03.0 PCI bridge: Apple Computer Inc. Shasta PCI Bridge (prog-
if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [70] #08 [8824]
0001:01:01.0 Network controller: Broadcom Corporation BCM4306 802.11b/
g Wireless LAN Controller (rev 03)
Subsystem: Apple Computer Inc.: Unknown device 004e
Flags: bus master, fast devsel, latency 16, IRQ 60
Memory at 80084000 (32-bit, non-prefetchable) [disabled]
Capabilities: [40] Power Management version 2
0001:01:07.0 Class ff00: Apple Computer Inc. Shasta Mac I/O
Flags: bus master, medium devsel, latency 16
Memory at 80000000 (32-bit, non-prefetchable)
0001:01:0b.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10
[OHCI])
Subsystem: NEC Corporation USB
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80082000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:01:0b.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10
[OHCI])
Subsystem: NEC Corporation USB
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80081000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:01:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-
if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Flags: bus master, medium devsel, latency 16, IRQ 70
Memory at 80080000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2
0001:02:0c.0 IDE interface: Broadcom (formerly ServerWorks) K2 SATA
(prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Broadcom (formerly ServerWorks) K2 SATA
Flags: bus master, 66Mhz, medium devsel, latency 16, IRQ 10
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
I/O ports at <unassigned> [disabled]
Memory at 80102000 (32-bit, non-prefetchable) [size=8K]
0001:02:0d.0 Class ff00: Apple Computer Inc. Shasta IDE
Flags: bus master, medium devsel, latency 32, IRQ 38
Memory at 80104000 (32-bit, non-prefetchable)
0001:02:0e.0 FireWire (IEEE 1394): Apple Computer Inc. Shasta
Firewire (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc.: Unknown device 5811
Flags: bus master, medium devsel, latency 248, IRQ 39
Memory at 80100000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2
0001:03:0f.0 Ethernet controller: Apple Computer Inc. Shasta (Sun GEM)
Flags: bus master, 66Mhz, slow devsel, latency 16, IRQ 40
Memory at 80400000 (32-bit, non-prefetchable) [size=80200000]
Expansion ROM at 00100000 [disabled]