Mailing List Archive

In your dial-peer can you use "forward-digits 3"?

Scott

-----Original Message-----
From: Ahmad Cheikh Moussa [mailto:acm@netuse.de]
Sent: Tuesday, June 29, 2004 4:19 AM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] Problem with call routing

Hi!

I have a cisco 3745 with c3745-ipvoice-mz.123-8.T.
I have on PRi attached to the cisco and one Cisco
Callmanager 3.3(4). My problem is that the router
makes a false translation.
Outgoing calls function properly, but incoming calls
are routed in the wrong direction.

Here an cut of my debug ouput :

*Mar 1 01:05:17.299 MET: H.225 SM: changing from H225_IDLE state to
H225_REQ_FS_SETUP state for callID 8
*Mar 1 01:05:17.507 MET: cch323_h225_receiver: received msg of type
SETUPIND_CHOSEN
*Mar 1 01:05:17.507 MET: setup_ind
*Mar 1 01:05:17.507 MET: setup_ind: callingNumber[4312390400]
calledNumber[0270]
*Mar 1 01:05:17.507 MET: setup_ind---- calling IE present

The problem here is that normaly the called number has to be "270"
and not "0270". Because of this 0 the call are routed to the PSTN.
The strange thing ist, that in the debug output before, the
called number was "270". During the whole call the called number
is correct, but as soon the call is directed to the callmanager
(H323 starts), the called number changed to "0270" and this is,
what I don't understand.

Any Ideas ?

Here a cut of the config of my router :

controller E1 1/0
pri-group timeslots 1-31
description ******
!
controller E1 1/1
shutdown
!
translation-rule 501
Rule 0 . 00
!
!
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
no cdp enable
!
voice-port 1/0:15
translate calling 501
cptone DE
!dial-peer voice 1 pots
description Default-Dial-peer fuer ausgehende Anrufe
max-conn 30
destination-pattern 0T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
!
dial-peer voice 101 voip
description Dial-Peer fuer Gespraeche zum CCM1
destination-pattern [1-2]..
session target ipv4:X.X.X.X
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
!
num-exp 821... ...
!

Tnaks in advance
Ahmad

--
Ahmad Cheikh-Moussa
NetUSE AG
Dr.-Hell-Straße, 24107 Kiel, Germany
Telefon: +49 431 2390 400 -- Telefax: +49 431 2390 499
Service: Service@NetUSE.DE -- http://NetUSE.DE/

_______________________________________________
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Hi!

The problem was produced by the ccm. In the gateway
configuration was the prefix DN set to 0.

I removed this setting and everything works fine.

Best regards,
Ahmad

P.S.: Thanks Jens!


Voll, Scott wrote:
> In your dial-peer can you use "forward-digits 3"?
>
> Scott
>
> -----Original Message-----
> From: Ahmad Cheikh Moussa [mailto:acm@netuse.de]
> Sent: Tuesday, June 29, 2004 4:19 AM
> To: cisco-voip@puck.nether.net
> Subject: [cisco-voip] Problem with call routing
>
> Hi!
>
> I have a cisco 3745 with c3745-ipvoice-mz.123-8.T.
> I have on PRi attached to the cisco and one Cisco
> Callmanager 3.3(4). My problem is that the router
> makes a false translation.
> Outgoing calls function properly, but incoming calls
> are routed in the wrong direction.
>
> Here an cut of my debug ouput :
>
> *Mar 1 01:05:17.299 MET: H.225 SM: changing from H225_IDLE state to
> H225_REQ_FS_SETUP state for callID 8
> *Mar 1 01:05:17.507 MET: cch323_h225_receiver: received msg of type
> SETUPIND_CHOSEN
> *Mar 1 01:05:17.507 MET: setup_ind
> *Mar 1 01:05:17.507 MET: setup_ind: callingNumber[4312390400]
> calledNumber[0270]
> *Mar 1 01:05:17.507 MET: setup_ind---- calling IE present
>
> The problem here is that normaly the called number has to be "270"
> and not "0270". Because of this 0 the call are routed to the PSTN.
> The strange thing ist, that in the debug output before, the
> called number was "270". During the whole call the called number
> is correct, but as soon the call is directed to the callmanager
> (H323 starts), the called number changed to "0270" and this is,
> what I don't understand.
>
> Any Ideas ?
>
> Here a cut of the config of my router :
>
> controller E1 1/0
> pri-group timeslots 1-31
> description ******
> !
> controller E1 1/1
> shutdown
> !
> translation-rule 501
> Rule 0 . 00
> !
> !
> interface Serial1/0:15
> no ip address
> no logging event link-status
> isdn switch-type primary-net5
> isdn overlap-receiving
> isdn incoming-voice voice
> no cdp enable
> !
> voice-port 1/0:15
> translate calling 501
> cptone DE
> !dial-peer voice 1 pots
> description Default-Dial-peer fuer ausgehende Anrufe
> max-conn 30
> destination-pattern 0T
> progress_ind alert enable 8
> direct-inward-dial
> port 1/0:15
> !
> dial-peer voice 101 voip
> description Dial-Peer fuer Gespraeche zum CCM1
> destination-pattern [1-2]..
> session target ipv4:X.X.X.X
> dtmf-relay h245-alphanumeric
> codec g711ulaw
> no vad
> !
> !
> num-exp 821... ...
> !
>
> Tnaks in advance
> Ahmad
>


--
Ahmad Cheikh-Moussa
NetUSE AG
Dr.-Hell-Straße, 24107 Kiel, Germany
Telefon: +49 431 2390 400 -- Telefax: +49 431 2390 499
Service: Service@NetUSE.DE -- http://NetUSE.DE/