two 26xx routers with fxo ports, regular telephones, a sip server/gatekeeper
if
you like, and a dial-plan that fits your needs - nothing too complex
there has been mention of a free ip-pbx that can do sip translation and
gatekeeper-type stuff, search the archives for the name (jared recommended
too ;) )
/joshua
"christos" <christos@thepipeline.net> wrote:
> Hi Scott
> I will follow up on all the leads. I am not provisionining this internally.
This is to
use my ISPs VoIP SIP gateway. They will provide the numbers and I need to
provide CPE dial tone. What I was very initially considering is driving the
voice
over with the data. This has to be low-end priced, i.e. netopia router with
cicso
ata-186 talking to a 2600 that would? uplink the data and send the sip/voip
traffic
to the gateway. I believe? this is simpler than provisioning VoIP internally
for an
enterprise? Thank you for the quick and depth of response.
> ----- Original Message -----
> From: Voll, Scott
> To: christos
> Cc: cisco-voip@puck.nether.net
> Sent: Wednesday, July 30, 2003 6:40 PM
> Subject: RE: [cisco-voip] newbee-voip
>
>
> We are just started our VoIP project. The 2621 is what we are using at
the
remote site and a 3640 at our hub site. Both routers will have IP Plus IOS
and a
NM-HDV-1T1-24 in each for the PRI to the PSTN. We are using 3550 24 port
inline power switches on the local LAN, 4k and 4500's are also options. You
will
also need the Cisco Call Manager for your routing of calls. You will need two
servers (Cisco OK'd) or you can look into the ICS 7750 for running the call
manager. We are running ours over Frame-Relay to this first site. Have you
contacted your local Cisco rep? They should be able to show you a demo. And
get you more into. If you do need to look into training, may I suggest
KnowledgeNet.com. Great price and good classes.
>
>
>
> For learning more start with this PDF I attached. I have a few more if
you
want them.
>
>
>
> Scott Voll
>
> Network Analyst, CCNA
>
> Willamette ESD
>
>
>
> -----Original Message-----
> From: christos [mailto:christos@thepipeline.net]
> Sent: Wednesday, July 30, 2003 2:56 PM
> To: Cisco
> Subject: [cisco-voip] newbee-voip
>
>
>
> Hi
>
> I hope I dont insult this list. I just want to know where to find how to
assemble
the minimal router, ios version, cpe for a small voip setup. I want to drive
it over
my existing data lines which would be either IP over T1, or frame. I am
thinking
about doing this in a 2600 chasis or a 3600 chasis. What is a recommended
configuration of router, cards, ios, cpe. Also please point me to where I can
quickly and accurately learn more. Thank you.
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-voip
>
"Walk with me through the Universe,
And along the way see how all of us are Connected.
Feast the eyes of your Soul,
On the Love that abounds.
In all places at once, seemingly endless,
Like your own existence."
- Stephen Hawking -
if
you like, and a dial-plan that fits your needs - nothing too complex
there has been mention of a free ip-pbx that can do sip translation and
gatekeeper-type stuff, search the archives for the name (jared recommended
too ;) )
/joshua
"christos" <christos@thepipeline.net> wrote:
> Hi Scott
> I will follow up on all the leads. I am not provisionining this internally.
This is to
use my ISPs VoIP SIP gateway. They will provide the numbers and I need to
provide CPE dial tone. What I was very initially considering is driving the
voice
over with the data. This has to be low-end priced, i.e. netopia router with
cicso
ata-186 talking to a 2600 that would? uplink the data and send the sip/voip
traffic
to the gateway. I believe? this is simpler than provisioning VoIP internally
for an
enterprise? Thank you for the quick and depth of response.
> ----- Original Message -----
> From: Voll, Scott
> To: christos
> Cc: cisco-voip@puck.nether.net
> Sent: Wednesday, July 30, 2003 6:40 PM
> Subject: RE: [cisco-voip] newbee-voip
>
>
> We are just started our VoIP project. The 2621 is what we are using at
the
remote site and a 3640 at our hub site. Both routers will have IP Plus IOS
and a
NM-HDV-1T1-24 in each for the PRI to the PSTN. We are using 3550 24 port
inline power switches on the local LAN, 4k and 4500's are also options. You
will
also need the Cisco Call Manager for your routing of calls. You will need two
servers (Cisco OK'd) or you can look into the ICS 7750 for running the call
manager. We are running ours over Frame-Relay to this first site. Have you
contacted your local Cisco rep? They should be able to show you a demo. And
get you more into. If you do need to look into training, may I suggest
KnowledgeNet.com. Great price and good classes.
>
>
>
> For learning more start with this PDF I attached. I have a few more if
you
want them.
>
>
>
> Scott Voll
>
> Network Analyst, CCNA
>
> Willamette ESD
>
>
>
> -----Original Message-----
> From: christos [mailto:christos@thepipeline.net]
> Sent: Wednesday, July 30, 2003 2:56 PM
> To: Cisco
> Subject: [cisco-voip] newbee-voip
>
>
>
> Hi
>
> I hope I dont insult this list. I just want to know where to find how to
assemble
the minimal router, ios version, cpe for a small voip setup. I want to drive
it over
my existing data lines which would be either IP over T1, or frame. I am
thinking
about doing this in a 2600 chasis or a 3600 chasis. What is a recommended
configuration of router, cards, ios, cpe. Also please point me to where I can
quickly and accurately learn more. Thank you.
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-voip
>
"Walk with me through the Universe,
And along the way see how all of us are Connected.
Feast the eyes of your Soul,
On the Love that abounds.
In all places at once, seemingly endless,
Like your own existence."
- Stephen Hawking -