Thank you Adam for the response .
The adaptors are ok because I have changed the slots .The cards works only at the first subslot .
Now I have changed again the cards and is this log :
Apr 15 12:12:06.982: %SEC-6-IPACCESSLOGS: list 50 denied 116.71.19.223 1 packet
Apr 15 12:14:41.319: %SPA_OIR-6-OFFLINECARD: SPA (SPA-5X1GE) offline in subslot 1/0
Apr 15 12:14:41.291: %SPA_OIR-DFC1-6-REMCARD: Card removed from Subslot 0, interfaces disabled
Apr 15 12:14:51.643: %C6K_WAN_C2W-DFC1-4-READERROR: C2Wire read failed reg 0x0000 on device SPA IDPROM
Apr 15 12:14:51.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD854 42ADDA30 42AE017C 42AE0680 42AE07E0 42AE0CE8
Apr 15 12:14:51.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD74C 42ADDA44 42AE017C 42AE0680 42AE07E0 42AE0CE8
Apr 15 12:14:51.643: %SPA_OIR-DFC1-6-INSCARD: Card inserted in Subslot 0
Apr 15 12:14:56.643: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA
Apr 15 12:14:56.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD854 42ADDA30 42AE017C 42AE0680 42AE07E0 42AE0CE8
Apr 15 12:14:56.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD74C 42ADDA44 42AE017C 42AE0680 42AE07E0 42AE0CE8
Apr 15 12:15:06.643: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA
Apr 15 12:15:16.643: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA
Apr 15 12:15:19.343: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD854 42ADDA30 42AE017C 42AE0680 42AE0928 42AE0AE0 42AE0BA8 42AE0CCC
Apr 15 12:15:19.343: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD74C 42ADDA44 42AE017C 42AE0680 42AE0928 42AE0AE0 42AE0BA8 42AE0CCC
Apr 15 12:15:26.643: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA
Apr 15 12:15:36.643: %SPA_OIR-3-RECOVERY_RELOAD: subslot 1/0: Attempting recovery by reloading SPA
Apr 15 12:15:41.643: %SPA_OIR-3-SPA_POWERED_OFF: subslot 1/0: SPA unknown powered off after 5 failures within 1200 seconds
Apr 15 12:15:41.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD854 42ADDA30 42AE017C 42AE0680 42AE07E0 42AE0CE8
Apr 15 12:15:41.643: %SPA-3-SW_ERROR: subslot 1/0 spa type 0x4: SNMP attributes not defined
-Traceback= 42ADD74C 42ADDA44 42AE017C 42AE0680 42AE07E0 42AE0CE8
the show module command :
7600#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 0 1-subslot SPA Interface Processor-600 7600-SIP-600 JAB094102E2
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE1238V8KE
5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL1243720U
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0015.621f.4880 to 0015.621f.48bf 1.0 12.2(18r)SX4 12.2(33)SRD Ok
3 0023.33fd.a780 to 0023.33fd.a7ff 2.5 12.2(33)SRD 12.2(33)SRD Ok
5 0016.9de6.bf24 to 0016.9de6.bf27 5.7 8.5(2) 12.2(33)SRD Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 SIP-600 Distributed Forward 7600-SIP-600-DC JAB094101LW 1.0 Ok
1/0 5xGE SPA SPA-5X1GE JAB100701EZ 2.2 OutSrvc
3/0 4xOC3 POS SPA SPA-4XOC3-POS JAE1233RW8W 1.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3BXL SAL124376TA 1.9 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1243759F 3.2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
1/0 Not Applicable
3 Pass
3/0 Pass
5 Pass
After this I have reset the module 1 :
7600#hw-module module 1 reset
The first slot is online after this .The show module command :
7600-BIG#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 5 1-subslot SPA Interface Processor-600 7600-SIP-600 JAB094102E2
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE1238V8KE
5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL1243720U
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0015.621f.4880 to 0015.621f.48bf 1.0 12.2(18r)SX4 12.2(33)SRD Ok
3 0023.33fd.a780 to 0023.33fd.a7ff 2.5 12.2(33)SRD 12.2(33)SRD Ok
5 0016.9de6.bf24 to 0016.9de6.bf27 5.7 8.5(2) 12.2(33)SRD Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 SIP-600 Distributed Forward 7600-SIP-600-DC JAB094101LW 1.0 Ok
1/0 5xGE SPA SPA-5X1GE JAB100701EZ 2.2 Ok
3/0 4xOC3 POS SPA SPA-4XOC3-POS JAE1233RW8W 1.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3BXL SAL124376TA 1.9 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1243759F 3.2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
1/0 Pass
3 Pass
3/0 Pass
5 Pass
the log after this reset is:
Apr 15 12:17:31.456: %C6KPWR-SP-4-DISABLED: power to module in slot 1 set off (Reset)
Apr 15 12:18:45.809: %CWAN_RP-6-CARDRELOAD: Module reloaded on slot 1/0
Apr 15 12:18:45.809: %OIR-6-INSCARD: Card inserted in slot 1, interfaces administratively shut down
Apr 15 10:18:47.493: %FABRIC_INTF_ASIC-DFC1-5-FABRICSYNC_DONE: Fabric ASIC 0 Channel 1: Fabric sync done.
Apr 15 12:18:54.439: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimal Diagnostics...
Apr 15 12:18:55.227: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
Apr 15 12:18:56.010: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
Apr 15 12:18:57.721: %DIAG-SP-6-RUN_MINIMUM: Module 1/0: Running Minimal Diagnostics...
Apr 15 12:18:55.457: %SCP-DFC1-5-ONLINE: Module online
Apr 15 12:19:12.753: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/0, changed state to down
Apr 15 12:19:13.189: %SPA_OIR-6-ONLINECARD: SPA (SPA-5X1GE) online in subslot 1/0
Apr 15 12:19:12.713: %DIAG-SP-6-DIAG_OK: Module 1/0: Passed Online Diagnostics
Apr 15 12:22:21.926: %SEC-6-IPACCESSLOGS: list 50 denied 200.252.29.132 1 packet
The IOS of the router is Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRD
This version do not suport the SIP 600 but I have upgrated with c7600-fpd-pkg.122-33.SRD.pkg After the upgrate of the IOS the SIP was recognised but with only subslot .
The type of the SIP 600 is with two subslots.
Maybe I have to change the IOS version of the router .SXF version
Regards
Ilir
----- Original Message -----
From: "Adam Armstrong" <lists@memetic.org>
To: "Ilir Nako" <inako@abcom.al>
Sent: Wednesday, April 15, 2009 11:41 AM
Subject: Re: [cisco-bba] SIP 600 : one subslot
> Do you see no syslog messages when you insert the second adaptor?
>
> Does the second adaptor work in the first subslot?
>
> Does the first adaptor still work in the second subslot?
>
> adam.
>
>> Hello
>>
>> I have installed a SIP 600 at one cisco 7600 router .I have inserted
>> two SPA 5xGE but only one of them is online .I see that the SIP seem
>> to be with only subslot active:
>> 7600#sh module
>> Mod Ports Card Type Model
>> Serial No.
>> --- ----- -------------------------------------- ------------------
>> -----------
>> 1 5 /1-subslot SPA Interface Processor-600/ 7600-SIP-600
>> 1/0 5xGE SPA SPA-5X1GE JAB093507M9
>> 2.2 Ok
>>
>> In this type of SIP 600 only one sublot can be used or is needed to
>> put some command to activate the other subslot ?
>>
>> Regards
>>
>> Ilir
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> cisco-bba mailing list
>> cisco-bba@puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-bba