Hi,
We are using Cisco AS5300/AS5350 with 4E1/8E1 lines gateway and R2
digitall signaling used to connect with Alcatel E10/Siemens EWSD voice
switch/PBX.
And we are trying change configuration of Cisco AS5300/AS5350 using
ISDN PRI signaling with Lucent Excel switch.
We done configuration on Lucent Excel switch using incoming
"EuroISDN", outgoing "ISDN IE".
On Cisco side following:
!
controller E1 2
pri-group timeslots 1-31
description Connected to Excel switch span 9
!
!
interface Serial2:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice modem
isdn send-alerting
isdn sending-complete
no cdp enable
!
E1 line never get up:
E1 2 is down.
Applique type is Channelized E1 - balanced
Description: Connected to Excel switch span 9
Receiver has remote alarm.
alarm-trigger is not set
Version info of slot 0: HW: 1, PLD Rev: 11
Framer Version: 0x8
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4B,
Board Hardware Version 3.1, Item Number 800-3881-02,
Board Revision D31, Serial Number 27517409,
PLD/ISP Version 0.1, Manufacture Date 19-Dec-2001.
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Data in current interval (159 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 159 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 159
Unavail Secs
Total Data (last 40 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 583 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 583
Unavail Secs
Could you send helpful advice? Also I didn't find any good
configuration/troubleshooting document on Cisco web.
Balgaa
We are using Cisco AS5300/AS5350 with 4E1/8E1 lines gateway and R2
digitall signaling used to connect with Alcatel E10/Siemens EWSD voice
switch/PBX.
And we are trying change configuration of Cisco AS5300/AS5350 using
ISDN PRI signaling with Lucent Excel switch.
We done configuration on Lucent Excel switch using incoming
"EuroISDN", outgoing "ISDN IE".
On Cisco side following:
!
controller E1 2
pri-group timeslots 1-31
description Connected to Excel switch span 9
!
!
interface Serial2:15
no ip address
isdn switch-type primary-net5
isdn incoming-voice modem
isdn send-alerting
isdn sending-complete
no cdp enable
!
E1 line never get up:
E1 2 is down.
Applique type is Channelized E1 - balanced
Description: Connected to Excel switch span 9
Receiver has remote alarm.
alarm-trigger is not set
Version info of slot 0: HW: 1, PLD Rev: 11
Framer Version: 0x8
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x4B,
Board Hardware Version 3.1, Item Number 800-3881-02,
Board Revision D31, Serial Number 27517409,
PLD/ISP Version 0.1, Manufacture Date 19-Dec-2001.
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Data in current interval (159 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 159 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 159
Unavail Secs
Total Data (last 40 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 583 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 583
Unavail Secs
Could you send helpful advice? Also I didn't find any good
configuration/troubleshooting document on Cisco web.
Balgaa