Mailing List Archive: Help w/ install and setup

Help w/ install and setup

Nov 9, 2004, 4:01 PM

Post #1 of 16 (12758 views)

I have spread and wackamole running on two Whitebox Linux machines.

whelmon1 - 10.1.11.202
whelmon2 - 10.1.11.203

my router is 10.1.11.254

I want them to serve the vip 10.1.11.206/32. See the bottom of the
message for my configs.

When I start spread on whelmon1, I get this printed:
# /usr/local/sbin/spread -n whelmon1
Conf_init: using file: /usr/local/etc/spread.conf
Successfully configured Segment 0 [10.1.11.255:4803] with 2 procs:
whelmon1: 10.1.11.202
whelmon2: 10.1.11.203
[root@whelmon1 :/usr/local/sbin]$ Membership id is ( 167840714, 1100044395)
--------------------
Configuration at whelmon1 is:
Num Segments 1
1 10.1.11.255 4803
whelmon1 10.1.11.202
====================

When I start spread on whelmon2,
# /usr/local/sbin/spread -n whelmon2
I get the same thing pretty much printed, then after a second, the
following is printed on each machine:

++++++++++++++++++++++
Num of groups: 0

I then run wackamole on whelmon1, and it brings up the 10.1.11.206
interfac e (here is the log lines)

Nov 9 15:55:39 whelmon1 wackamole[3403]: connecting to 4803
Nov 9 15:55:39 whelmon1 wackamole[3403]: 934 No such interface
Nov 9 15:55:44 whelmon1 wackamole[3403]: UP:
eth0:1:10.1.11.206/255.255.255.255
Nov 9 15:55:44 whelmon1 wackamole[3403]: Re-queued arp spoof notifier
for virtual entry.

BUT - when I run wackamole on whelmon2, nothing happens, all I ever
get in the logs is:

Nov 9 15:56:24 whelmon2 wackamole[25450]: connecting to 4803
Nov 9 15:56:24 whelmon2 wackamole[25450]: 934 No such interface

I tried simulating a failure on whelmon1 and seeing if whelmon2 took
the IP (I thought maybe it was working, but was not very verbose about
it), and 10.1.11.206 disappeared, so no dice.

This is a whole lot of info to weed through, but I am trying to get
some suggestions on what I should do next to troubleshoot. It seems
like I am close, but something is missing such that whelmon2 doesn't
want to join in.

Thanks

Here is my spread.conf:

Spread_Segment 10.1.11.255:4803 {
whelmon1 10.1.11.202
whelmon2 10.1.11.203
}

And here is my wackamole.conf:

Spread = 4803
SpreadRetryInterval = 5s
Group = wack1
Control = /var/run/wack.it
Prefer None
VirtualInterfaces {
eth0:10.1.11.206/32
}
Notify {
eth0:10.1.1.254/32
arp-cache
}
balance {
AcquisitionsPerRound = all
interval = 4s
}

mature = 5s

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #2 of 16 (12473 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #3 of 16 (12488 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #4 of 16 (12455 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #5 of 16 (12451 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #6 of 16 (12463 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:01 PM

Post #7 of 16 (12469 views)

Permalink

Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 4:14 PM

Post #8 of 16 (12453 views)

Permalink

Re: Help w/ install and setup [ In reply to ]

rcaudy at gmail

Nov 9, 2004, 4:18 PM

Post #9 of 16 (12510 views)

Permalink

Well, to begin with, from the info you copied it looks like the Spread
daemons aren't finding one another, since the configuration that
whelmon1 installs is just whelmon1. Could you double check that they
*are* able to communicate, and that they do install a configuration
with both of them?

Cheers,
Ryan

On Tue, 9 Nov 2004 16:01:30 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> I have spread and wackamole running on two Whitebox Linux machines.
>
> whelmon1 - 10.1.11.202
> whelmon2 - 10.1.11.203
>
> my router is 10.1.11.254
>
> I want them to serve the vip 10.1.11.206/32. See the bottom of the
> message for my configs.
>
> When I start spread on whelmon1, I get this printed:
> # /usr/local/sbin/spread -n whelmon1
> Conf_init: using file: /usr/local/etc/spread.conf
> Successfully configured Segment 0 [10.1.11.255:4803] with 2 procs:
> whelmon1: 10.1.11.202
> whelmon2: 10.1.11.203
> [root@whelmon1 :/usr/local/sbin]$ Membership id is ( 167840714, 1100044395)
> --------------------
> Configuration at whelmon1 is:
> Num Segments 1
> 1 10.1.11.255 4803
> whelmon1 10.1.11.202
> ====================
>
> When I start spread on whelmon2,
> # /usr/local/sbin/spread -n whelmon2
> I get the same thing pretty much printed, then after a second, the
> following is printed on each machine:
>
> ++++++++++++++++++++++
> Num of groups: 0
>
> I then run wackamole on whelmon1, and it brings up the 10.1.11.206
> interfac e (here is the log lines)
>
> Nov 9 15:55:39 whelmon1 wackamole[3403]: connecting to 4803
> Nov 9 15:55:39 whelmon1 wackamole[3403]: 934 No such interface
> Nov 9 15:55:44 whelmon1 wackamole[3403]: UP:
> eth0:1:10.1.11.206/255.255.255.255
> Nov 9 15:55:44 whelmon1 wackamole[3403]: Re-queued arp spoof notifier
> for virtual entry.
>
> BUT - when I run wackamole on whelmon2, nothing happens, all I ever
> get in the logs is:
>
> Nov 9 15:56:24 whelmon2 wackamole[25450]: connecting to 4803
> Nov 9 15:56:24 whelmon2 wackamole[25450]: 934 No such interface
>
> I tried simulating a failure on whelmon1 and seeing if whelmon2 took
> the IP (I thought maybe it was working, but was not very verbose about
> it), and 10.1.11.206 disappeared, so no dice.
>
> This is a whole lot of info to weed through, but I am trying to get
> some suggestions on what I should do next to troubleshoot. It seems
> like I am close, but something is missing such that whelmon2 doesn't
> want to join in.
>
> Thanks
>
> Here is my spread.conf:
>
> Spread_Segment 10.1.11.255:4803 {
> whelmon1 10.1.11.202
> whelmon2 10.1.11.203
> }
>
> And here is my wackamole.conf:
>
> Spread = 4803
> SpreadRetryInterval = 5s
> Group = wack1
> Control = /var/run/wack.it
> Prefer None
> VirtualInterfaces {
> eth0:10.1.11.206/32
> }
> Notify {
> eth0:10.1.1.254/32
> arp-cache
> }
> balance {
> AcquisitionsPerRound = all
> interval = 4s
> }
>
> mature = 5s
>
> _______________________________________________
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

--
---------------------------------------------------------------------
Ryan W. Caudy
<rcaudy@gmail.com>
---------------------------------------------------------------------
Bloomberg L.P.
<rcaudy1@bloomberg.net>
---------------------------------------------------------------------
[Alumnus]
<caudy@cnds.jhu.edu>
Center for Networking and Distributed Systems
Department of Computer Science
Johns Hopkins University
---------------------------------------------------------------------

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 9, 2004, 5:17 PM

Post #10 of 16 (12493 views)

Permalink

What part of my config looked like it was only for whelmon1? I have
both whelmon1 and whelmon2 defined in my spread.confg

Here is the output from spmonitor run from whelmon1 as:
# spmonitor -n whelmon1

=============
Activate Status
-------------

Enter Proc Name: whelmon1
Enter Proc Name: whelmon2
Enter Proc Name:
Monitor: send status query

============================
Status at whelmon1 V 3.17. 3 (state 1, gstate 1) after 4834 seconds :
Membership : 2 procs in 1 segments, leader is whelmon1
rounds : 2452 tok_hurry : 2412 memb change: 1
sent pack: 8 recv pack : 6 retrans : 0
u retrans: 0 s retrans : 0 b retrans : 0
My_aru : 17 Aru : 17 Highest seq: 17
Sessions : 1 Groups : 1 Window : 60
Deliver M: 13 Deliver Pk: 17 Pers Window: 15
Delta Mes: 13 Delta Pack: 17 Delta sec : 4834
==================================

============================
Status at whelmon2 V 3.17. 3 (state 1, gstate 1) after 4930 seconds :
Membership : 2 procs in 1 segments, leader is whelmon1
rounds : 2497 tok_hurry : 2452 memb change: 2
sent pack: 7 recv pack : 9 retrans : 0
u retrans: 0 s retrans : 0 b retrans : 0
My_aru : 17 Aru : 17 Highest seq: 17
Sessions : 1 Groups : 1 Window : 60
Deliver M: 13 Deliver Pk: 19 Pers Window: 15
Delta Mes: 0 Delta Pack: 0 Delta sec : 96
==================================

On Tue, 9 Nov 2004 19:18:36 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> Well, to begin with, from the info you copied it looks like the Spread
> daemons aren't finding one another, since the configuration that
> whelmon1 installs is just whelmon1. Could you double check that they
> *are* able to communicate, and that they do install a configuration
> with both of them?
>
> Cheers,
> Ryan
>
>
>
>
> On Tue, 9 Nov 2004 16:01:30 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > I have spread and wackamole running on two Whitebox Linux machines.
> >
> > whelmon1 - 10.1.11.202
> > whelmon2 - 10.1.11.203
> >
> > my router is 10.1.11.254
> >
> > I want them to serve the vip 10.1.11.206/32. See the bottom of the
> > message for my configs.
> >
> > When I start spread on whelmon1, I get this printed:
> > # /usr/local/sbin/spread -n whelmon1
> > Conf_init: using file: /usr/local/etc/spread.conf
> > Successfully configured Segment 0 [10.1.11.255:4803] with 2 procs:
> > whelmon1: 10.1.11.202
> > whelmon2: 10.1.11.203
> > [root@whelmon1 :/usr/local/sbin]$ Membership id is ( 167840714, 1100044395)
> > --------------------
> > Configuration at whelmon1 is:
> > Num Segments 1
> > 1 10.1.11.255 4803
> > whelmon1 10.1.11.202
> > ====================
> >
> > When I start spread on whelmon2,
> > # /usr/local/sbin/spread -n whelmon2
> > I get the same thing pretty much printed, then after a second, the
> > following is printed on each machine:
> >
> > ++++++++++++++++++++++
> > Num of groups: 0
> >
> > I then run wackamole on whelmon1, and it brings up the 10.1.11.206
> > interfac e (here is the log lines)
> >
> > Nov 9 15:55:39 whelmon1 wackamole[3403]: connecting to 4803
> > Nov 9 15:55:39 whelmon1 wackamole[3403]: 934 No such interface
> > Nov 9 15:55:44 whelmon1 wackamole[3403]: UP:
> > eth0:1:10.1.11.206/255.255.255.255
> > Nov 9 15:55:44 whelmon1 wackamole[3403]: Re-queued arp spoof notifier
> > for virtual entry.
> >
> > BUT - when I run wackamole on whelmon2, nothing happens, all I ever
> > get in the logs is:
> >
> > Nov 9 15:56:24 whelmon2 wackamole[25450]: connecting to 4803
> > Nov 9 15:56:24 whelmon2 wackamole[25450]: 934 No such interface
> >
> > I tried simulating a failure on whelmon1 and seeing if whelmon2 took
> > the IP (I thought maybe it was working, but was not very verbose about
> > it), and 10.1.11.206 disappeared, so no dice.
> >
> > This is a whole lot of info to weed through, but I am trying to get
> > some suggestions on what I should do next to troubleshoot. It seems
> > like I am close, but something is missing such that whelmon2 doesn't
> > want to join in.
> >
> > Thanks
> >
> > Here is my spread.conf:
> >
> > Spread_Segment 10.1.11.255:4803 {
> > whelmon1 10.1.11.202
> > whelmon2 10.1.11.203
> > }
> >
> > And here is my wackamole.conf:
> >
> > Spread = 4803
> > SpreadRetryInterval = 5s
> > Group = wack1
> > Control = /var/run/wack.it
> > Prefer None
> > VirtualInterfaces {
> > eth0:10.1.11.206/32
> > }
> > Notify {
> > eth0:10.1.1.254/32
> > arp-cache
> > }
> > balance {
> > AcquisitionsPerRound = all
> > interval = 4s
> > }
> >
> > mature = 5s
> >
> > _______________________________________________
> > wackamole-users mailing list
> > wackamole-users@lists.backhand.org
> > http://lists.backhand.org/mailman/listinfo/wackamole-users
> >
>
> --
> ---------------------------------------------------------------------
> Ryan W. Caudy
> <rcaudy@gmail.com>
> ---------------------------------------------------------------------
> Bloomberg L.P.
> <rcaudy1@bloomberg.net>
> ---------------------------------------------------------------------
> [Alumnus]
> <caudy@cnds.jhu.edu>
> Center for Networking and Distributed Systems
> Department of Computer Science
> Johns Hopkins University
> ---------------------------------------------------------------------
>
> _______________________________________________
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

rcaudy at gmail

Nov 9, 2004, 5:25 PM

Post #11 of 16 (12509 views)

Permalink

Sorry, this part:

Configuration at whelmon1 is:
Num Segments 1
1 10.1.11.255 4803
whelmon1 10.1.11.202

I wasn't talking about the spread.conf config, but rather the
configuration installed by the daemons after they completed the daemon
membership algorithm.

However, your spmonitor output answered my question.

Cheers,
Ryan

On Tue, 9 Nov 2004 17:17:51 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> What part of my config looked like it was only for whelmon1? I have
> both whelmon1 and whelmon2 defined in my spread.confg
>
> Here is the output from spmonitor run from whelmon1 as:
> # spmonitor -n whelmon1
>
> =============
> Activate Status
> -------------
>
> Enter Proc Name: whelmon1
> Enter Proc Name: whelmon2
> Enter Proc Name:
> Monitor: send status query
>
> Monitor>
> ============================
> Status at whelmon1 V 3.17. 3 (state 1, gstate 1) after 4834 seconds :
> Membership : 2 procs in 1 segments, leader is whelmon1
> rounds : 2452 tok_hurry : 2412 memb change: 1
> sent pack: 8 recv pack : 6 retrans : 0
> u retrans: 0 s retrans : 0 b retrans : 0
> My_aru : 17 Aru : 17 Highest seq: 17
> Sessions : 1 Groups : 1 Window : 60
> Deliver M: 13 Deliver Pk: 17 Pers Window: 15
> Delta Mes: 13 Delta Pack: 17 Delta sec : 4834
> ==================================
>
> Monitor>
> ============================
> Status at whelmon2 V 3.17. 3 (state 1, gstate 1) after 4930 seconds :
> Membership : 2 procs in 1 segments, leader is whelmon1
> rounds : 2497 tok_hurry : 2452 memb change: 2
> sent pack: 7 recv pack : 9 retrans : 0
> u retrans: 0 s retrans : 0 b retrans : 0
> My_aru : 17 Aru : 17 Highest seq: 17
> Sessions : 1 Groups : 1 Window : 60
> Deliver M: 13 Deliver Pk: 19 Pers Window: 15
> Delta Mes: 0 Delta Pack: 0 Delta sec : 96
> ==================================
>
>
>
>
> On Tue, 9 Nov 2004 19:18:36 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> > Well, to begin with, from the info you copied it looks like the Spread
> > daemons aren't finding one another, since the configuration that
> > whelmon1 installs is just whelmon1. Could you double check that they
> > *are* able to communicate, and that they do install a configuration
> > with both of them?
> >
> > Cheers,
> > Ryan
> >
> >
> >
> >
> > On Tue, 9 Nov 2004 16:01:30 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > > I have spread and wackamole running on two Whitebox Linux machines.
> > >
> > > whelmon1 - 10.1.11.202
> > > whelmon2 - 10.1.11.203
> > >
> > > my router is 10.1.11.254
> > >
> > > I want them to serve the vip 10.1.11.206/32. See the bottom of the
> > > message for my configs.
> > >
> > > When I start spread on whelmon1, I get this printed:
> > > # /usr/local/sbin/spread -n whelmon1
> > > Conf_init: using file: /usr/local/etc/spread.conf
> > > Successfully configured Segment 0 [10.1.11.255:4803] with 2 procs:
> > > whelmon1: 10.1.11.202
> > > whelmon2: 10.1.11.203
> > > [root@whelmon1 :/usr/local/sbin]$ Membership id is ( 167840714, 1100044395)
> > > --------------------
> > > Configuration at whelmon1 is:
> > > Num Segments 1
> > > 1 10.1.11.255 4803
> > > whelmon1 10.1.11.202
> > > ====================
> > >
> > > When I start spread on whelmon2,
> > > # /usr/local/sbin/spread -n whelmon2
> > > I get the same thing pretty much printed, then after a second, the
> > > following is printed on each machine:
> > >
> > > ++++++++++++++++++++++
> > > Num of groups: 0
> > >
> > > I then run wackamole on whelmon1, and it brings up the 10.1.11.206
> > > interfac e (here is the log lines)
> > >
> > > Nov 9 15:55:39 whelmon1 wackamole[3403]: connecting to 4803
> > > Nov 9 15:55:39 whelmon1 wackamole[3403]: 934 No such interface
> > > Nov 9 15:55:44 whelmon1 wackamole[3403]: UP:
> > > eth0:1:10.1.11.206/255.255.255.255
> > > Nov 9 15:55:44 whelmon1 wackamole[3403]: Re-queued arp spoof notifier
> > > for virtual entry.
> > >
> > > BUT - when I run wackamole on whelmon2, nothing happens, all I ever
> > > get in the logs is:
> > >
> > > Nov 9 15:56:24 whelmon2 wackamole[25450]: connecting to 4803
> > > Nov 9 15:56:24 whelmon2 wackamole[25450]: 934 No such interface
> > >
> > > I tried simulating a failure on whelmon1 and seeing if whelmon2 took
> > > the IP (I thought maybe it was working, but was not very verbose about
> > > it), and 10.1.11.206 disappeared, so no dice.
> > >
> > > This is a whole lot of info to weed through, but I am trying to get
> > > some suggestions on what I should do next to troubleshoot. It seems
> > > like I am close, but something is missing such that whelmon2 doesn't
> > > want to join in.
> > >
> > > Thanks
> > >
> > > Here is my spread.conf:
> > >
> > > Spread_Segment 10.1.11.255:4803 {
> > > whelmon1 10.1.11.202
> > > whelmon2 10.1.11.203
> > > }
> > >
> > > And here is my wackamole.conf:
> > >
> > > Spread = 4803
> > > SpreadRetryInterval = 5s
> > > Group = wack1
> > > Control = /var/run/wack.it
> > > Prefer None
> > > VirtualInterfaces {
> > > eth0:10.1.11.206/32
> > > }
> > > Notify {
> > > eth0:10.1.1.254/32
> > > arp-cache
> > > }
> > > balance {
> > > AcquisitionsPerRound = all
> > > interval = 4s
> > > }
> > >
> > > mature = 5s
> > >
> > > _______________________________________________
> > > wackamole-users mailing list
> > > wackamole-users@lists.backhand.org
> > > http://lists.backhand.org/mailman/listinfo/wackamole-users
> > >
> >
> > --
> > ---------------------------------------------------------------------
> > Ryan W. Caudy
> > <rcaudy@gmail.com>
> > ---------------------------------------------------------------------
> > Bloomberg L.P.
> > <rcaudy1@bloomberg.net>
> > ---------------------------------------------------------------------
> > [Alumnus]
> > <caudy@cnds.jhu.edu>
> > Center for Networking and Distributed Systems
> > Department of Computer Science
> > Johns Hopkins University
> > ---------------------------------------------------------------------
> >
> > _______________________________________________
> > wackamole-users mailing list
> > wackamole-users@lists.backhand.org
> > http://lists.backhand.org/mailman/listinfo/wackamole-users
> >
>
> _______________________________________________
>
>
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

--
---------------------------------------------------------------------
Ryan W. Caudy
<rcaudy@gmail.com>
---------------------------------------------------------------------
Bloomberg L.P.
<rcaudy1@bloomberg.net>
---------------------------------------------------------------------
[Alumnus]
<caudy@cnds.jhu.edu>
Center for Networking and Distributed Systems
Department of Computer Science
Johns Hopkins University
---------------------------------------------------------------------

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 10, 2004, 8:40 AM

Post #12 of 16 (12510 views)

Permalink

On Tue, 9 Nov 2004 20:25:30 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> Sorry, this part:
>
> Configuration at whelmon1 is:
> Num Segments 1
> 1 10.1.11.255 4803
> whelmon1 10.1.11.202
>
> I wasn't talking about the spread.conf config, but rather the
> configuration installed by the daemons after they completed the daemon
> membership algorithm.
>
> However, your spmonitor output answered my question.

Any other thoughts of how I can troubleshoot?

>
>
>
> Cheers,
> Ryan
>
> On Tue, 9 Nov 2004 17:17:51 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > What part of my config looked like it was only for whelmon1? I have
> > both whelmon1 and whelmon2 defined in my spread.confg
> >
> > Here is the output from spmonitor run from whelmon1 as:
> > # spmonitor -n whelmon1
> >
> > =============
> > Activate Status
> > -------------
> >
> > Enter Proc Name: whelmon1
> > Enter Proc Name: whelmon2
> > Enter Proc Name:
> > Monitor: send status query
> >
> > Monitor>
> > ============================
> > Status at whelmon1 V 3.17. 3 (state 1, gstate 1) after 4834 seconds :
> > Membership : 2 procs in 1 segments, leader is whelmon1
> > rounds : 2452 tok_hurry : 2412 memb change: 1
> > sent pack: 8 recv pack : 6 retrans : 0
> > u retrans: 0 s retrans : 0 b retrans : 0
> > My_aru : 17 Aru : 17 Highest seq: 17
> > Sessions : 1 Groups : 1 Window : 60
> > Deliver M: 13 Deliver Pk: 17 Pers Window: 15
> > Delta Mes: 13 Delta Pack: 17 Delta sec : 4834
> > ==================================
> >
> > Monitor>
> > ============================
> > Status at whelmon2 V 3.17. 3 (state 1, gstate 1) after 4930 seconds :
> > Membership : 2 procs in 1 segments, leader is whelmon1
> > rounds : 2497 tok_hurry : 2452 memb change: 2
> > sent pack: 7 recv pack : 9 retrans : 0
> > u retrans: 0 s retrans : 0 b retrans : 0
> > My_aru : 17 Aru : 17 Highest seq: 17
> > Sessions : 1 Groups : 1 Window : 60
> > Deliver M: 13 Deliver Pk: 19 Pers Window: 15
> > Delta Mes: 0 Delta Pack: 0 Delta sec : 96
> > ==================================
> >
> >
> >
> >
> > On Tue, 9 Nov 2004 19:18:36 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> > > Well, to begin with, from the info you copied it looks like the Spread
> > > daemons aren't finding one another, since the configuration that
> > > whelmon1 installs is just whelmon1. Could you double check that they
> > > *are* able to communicate, and that they do install a configuration
> > > with both of them?
> > >
> > > Cheers,
> > > Ryan
> > >
> > >
> > >
> > >
> > > On Tue, 9 Nov 2004 16:01:30 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > > > I have spread and wackamole running on two Whitebox Linux machines.
> > > >
> > > > whelmon1 - 10.1.11.202
> > > > whelmon2 - 10.1.11.203
> > > >
> > > > my router is 10.1.11.254
> > > >
> > > > I want them to serve the vip 10.1.11.206/32. See the bottom of the
> > > > message for my configs.
> > > >
> > > > When I start spread on whelmon1, I get this printed:
> > > > # /usr/local/sbin/spread -n whelmon1
> > > > Conf_init: using file: /usr/local/etc/spread.conf
> > > > Successfully configured Segment 0 [10.1.11.255:4803] with 2 procs:
> > > > whelmon1: 10.1.11.202
> > > > whelmon2: 10.1.11.203
> > > > [root@whelmon1 :/usr/local/sbin]$ Membership id is ( 167840714, 1100044395)
> > > > --------------------
> > > > Configuration at whelmon1 is:
> > > > Num Segments 1
> > > > 1 10.1.11.255 4803
> > > > whelmon1 10.1.11.202
> > > > ====================
> > > >
> > > > When I start spread on whelmon2,
> > > > # /usr/local/sbin/spread -n whelmon2
> > > > I get the same thing pretty much printed, then after a second, the
> > > > following is printed on each machine:
> > > >
> > > > ++++++++++++++++++++++
> > > > Num of groups: 0
> > > >
> > > > I then run wackamole on whelmon1, and it brings up the 10.1.11.206
> > > > interfac e (here is the log lines)
> > > >
> > > > Nov 9 15:55:39 whelmon1 wackamole[3403]: connecting to 4803
> > > > Nov 9 15:55:39 whelmon1 wackamole[3403]: 934 No such interface
> > > > Nov 9 15:55:44 whelmon1 wackamole[3403]: UP:
> > > > eth0:1:10.1.11.206/255.255.255.255
> > > > Nov 9 15:55:44 whelmon1 wackamole[3403]: Re-queued arp spoof notifier
> > > > for virtual entry.
> > > >
> > > > BUT - when I run wackamole on whelmon2, nothing happens, all I ever
> > > > get in the logs is:
> > > >
> > > > Nov 9 15:56:24 whelmon2 wackamole[25450]: connecting to 4803
> > > > Nov 9 15:56:24 whelmon2 wackamole[25450]: 934 No such interface
> > > >
> > > > I tried simulating a failure on whelmon1 and seeing if whelmon2 took
> > > > the IP (I thought maybe it was working, but was not very verbose about
> > > > it), and 10.1.11.206 disappeared, so no dice.
> > > >
> > > > This is a whole lot of info to weed through, but I am trying to get
> > > > some suggestions on what I should do next to troubleshoot. It seems
> > > > like I am close, but something is missing such that whelmon2 doesn't
> > > > want to join in.
> > > >
> > > > Thanks
> > > >
> > > > Here is my spread.conf:
> > > >
> > > > Spread_Segment 10.1.11.255:4803 {
> > > > whelmon1 10.1.11.202
> > > > whelmon2 10.1.11.203
> > > > }
> > > >
> > > > And here is my wackamole.conf:
> > > >
> > > > Spread = 4803
> > > > SpreadRetryInterval = 5s
> > > > Group = wack1
> > > > Control = /var/run/wack.it
> > > > Prefer None
> > > > VirtualInterfaces {
> > > > eth0:10.1.11.206/32
> > > > }
> > > > Notify {
> > > > eth0:10.1.1.254/32
> > > > arp-cache
> > > > }
> > > > balance {
> > > > AcquisitionsPerRound = all
> > > > interval = 4s
> > > > }
> > > >
> > > > mature = 5s
> > > >
> > > > _______________________________________________
> > > > wackamole-users mailing list
> > > > wackamole-users@lists.backhand.org
> > > > http://lists.backhand.org/mailman/listinfo/wackamole-users
> > > >
> > >
> > > --
> > > ---------------------------------------------------------------------
> > > Ryan W. Caudy
> > > <rcaudy@gmail.com>
> > > ---------------------------------------------------------------------
> > > Bloomberg L.P.
> > > <rcaudy1@bloomberg.net>
> > > ---------------------------------------------------------------------
> > > [Alumnus]
> > > <caudy@cnds.jhu.edu>
> > > Center for Networking and Distributed Systems
> > > Department of Computer Science
> > > Johns Hopkins University
> > > ---------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > wackamole-users mailing list
> > > wackamole-users@lists.backhand.org
> > > http://lists.backhand.org/mailman/listinfo/wackamole-users
> > >
> >
> > _______________________________________________
>
>
> >
> >
> > wackamole-users mailing list
> > wackamole-users@lists.backhand.org
> > http://lists.backhand.org/mailman/listinfo/wackamole-users
> >
>
> --
> ---------------------------------------------------------------------
> Ryan W. Caudy
> <rcaudy@gmail.com>
> ---------------------------------------------------------------------
> Bloomberg L.P.
> <rcaudy1@bloomberg.net>
> ---------------------------------------------------------------------
> [Alumnus]
> <caudy@cnds.jhu.edu>
> Center for Networking and Distributed Systems
> Department of Computer Science
> Johns Hopkins University
> ---------------------------------------------------------------------
>
> _______________________________________________
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

rcaudy at gmail

Nov 10, 2004, 4:18 PM

Post #13 of 16 (12497 views)

Permalink

On Wed, 10 Nov 2004 08:40:50 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
>
> Any other thoughts of how I can troubleshoot?
>

Try using wackamole's "-d" option to turn on more debugging info.
Other than that, I'd be concerned about the "No such interface"
printout, but I'm not to familiar with that area of the code. Maybe
Theo has some advice.

Cheers,
Ryan

--
---------------------------------------------------------------------
Ryan W. Caudy
<rcaudy@gmail.com>
---------------------------------------------------------------------
Bloomberg L.P.
<rcaudy1@bloomberg.net>
---------------------------------------------------------------------
[Alumnus]
<caudy@cnds.jhu.edu>
Center for Networking and Distributed Systems
Department of Computer Science
Johns Hopkins University
---------------------------------------------------------------------

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

kickdaddy at gmail

Nov 12, 2004, 12:11 PM

Post #14 of 16 (12523 views)

Permalink

I run it (wackamole -d) on machine 1, all works good, I then run it on machine 2

vwackamole: wackamole.c:702: Send_state_message: Assertion `ret ==
My.num_allocated' failed.
Aborted

That happens everytime I fire up the second wackamole instance on the
second machine (I can even switch order I launch them, and it will
happen on the other machine)

On Wed, 10 Nov 2004 19:18:49 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> On Wed, 10 Nov 2004 08:40:50 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> >
> > Any other thoughts of how I can troubleshoot?
> >
>
> Try using wackamole's "-d" option to turn on more debugging info.
> Other than that, I'd be concerned about the "No such interface"
> printout, but I'm not to familiar with that area of the code. Maybe
> Theo has some advice.
>
> Cheers,
> Ryan
>
> --
> ---------------------------------------------------------------------
>
>
> Ryan W. Caudy
> <rcaudy@gmail.com>
> ---------------------------------------------------------------------
> Bloomberg L.P.
> <rcaudy1@bloomberg.net>
> ---------------------------------------------------------------------
> [Alumnus]
> <caudy@cnds.jhu.edu>
> Center for Networking and Distributed Systems
> Department of Computer Science
> Johns Hopkins University
> ---------------------------------------------------------------------
>
> _______________________________________________
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

rcaudy at gmail

Nov 12, 2004, 7:55 PM

Post #15 of 16 (12506 views)

Permalink

On Nov. 1, someone else e-mailed with the same assertion failure.
Theo suggested to them that it may be a problem with configuration
files that differ between different Wackamole daemon instances -- they
should only differ, if at all, in the "prefer" clause. I can't do it
tonight, but I'll try to track down the meaning of that assertion this
weekend -- I would bet it's from the Wackamole daemon state exchange
in wackamole.c.

Cheers,
Ryan

On Fri, 12 Nov 2004 12:11:59 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> I run it (wackamole -d) on machine 1, all works good, I then run it on machine 2
>
> vwackamole: wackamole.c:702: Send_state_message: Assertion `ret ==
> My.num_allocated' failed.
> Aborted
>
> That happens everytime I fire up the second wackamole instance on the
> second machine (I can even switch order I launch them, and it will
> happen on the other machine)
>
>
>
>
> On Wed, 10 Nov 2004 19:18:49 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> > On Wed, 10 Nov 2004 08:40:50 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > >
> > > Any other thoughts of how I can troubleshoot?
> > >
> >
> > Try using wackamole's "-d" option to turn on more debugging info.
> > Other than that, I'd be concerned about the "No such interface"
> > printout, but I'm not to familiar with that area of the code. Maybe
> > Theo has some advice.
> >
> > Cheers,
> > Ryan
> >
> > --
> > ---------------------------------------------------------------------
> >
> >
> > Ryan W. Caudy
> > <rcaudy@gmail.com>
> > ---------------------------------------------------------------------
> > Bloomberg L.P.
> > <rcaudy1@bloomberg.net>
> > ---------------------------------------------------------------------
> > [Alumnus]
> > <caudy@cnds.jhu.edu>
> > Center for Networking and Distributed Systems
> > Department of Computer Science
> > Johns Hopkins University
> > ---------------------------------------------------------------------
> >
> > _______________________________________________
> > wackamole-users mailing list
> > wackamole-users@lists.backhand.org
> > http://lists.backhand.org/mailman/listinfo/wackamole-users
> >
>
> _______________________________________________
> wackamole-users mailing list
> wackamole-users@lists.backhand.org
> http://lists.backhand.org/mailman/listinfo/wackamole-users
>

--
---------------------------------------------------------------------
Ryan W. Caudy
<rcaudy@gmail.com>
---------------------------------------------------------------------
Bloomberg L.P.
<rcaudy1@bloomberg.net>
---------------------------------------------------------------------
[Alumnus]
<caudy@cnds.jhu.edu>
Center for Networking and Distributed Systems
Department of Computer Science
Johns Hopkins University
---------------------------------------------------------------------

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users

Re: Help w/ install and setup [ In reply to ]

rcaudy at gmail

Nov 14, 2004, 6:48 PM

Post #16 of 16 (12539 views)

Permalink

I looked further into this. I don't see that this should be related
to the configuration file, at least not in the most recent version of
the source code I have. The assertion "ret == My.num_allocated" is in
the function that builds state messages, for the Wackamole state
exchange. It's a basic sanity check -- the daemon packs one section
of the state message with each interface that is assigned to it,
according to the Old_table, the last consistent copy of the
Allocation_table. My.num_allocated should always be the same as the
number of interfaces that match this daemon. I don't see any bugs in
the way this variable is being changed, in my copy of the source code.
Do you know if it's maybe being overwritten somehow?

Cheers,
Ryan

On Fri, 12 Nov 2004 22:55:57 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> On Nov. 1, someone else e-mailed with the same assertion failure.
> Theo suggested to them that it may be a problem with configuration
> files that differ between different Wackamole daemon instances -- they
> should only differ, if at all, in the "prefer" clause. I can't do it
> tonight, but I'll try to track down the meaning of that assertion this
> weekend -- I would bet it's from the Wackamole daemon state exchange
> in wackamole.c.
>
> Cheers,
> Ryan
>
>
>
> On Fri, 12 Nov 2004 12:11:59 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > I run it (wackamole -d) on machine 1, all works good, I then run it on machine 2
> >
> > vwackamole: wackamole.c:702: Send_state_message: Assertion `ret ==
> > My.num_allocated' failed.
> > Aborted
> >
> > That happens everytime I fire up the second wackamole instance on the
> > second machine (I can even switch order I launch them, and it will
> > happen on the other machine)
> >
> >
> >
> >
> > On Wed, 10 Nov 2004 19:18:49 -0500, Ryan Caudy <rcaudy@gmail.com> wrote:
> > > On Wed, 10 Nov 2004 08:40:50 -0800, Sean Leach <kickdaddy@gmail.com> wrote:
> > > >
> > > > Any other thoughts of how I can troubleshoot?
> > > >
> > >
> > > Try using wackamole's "-d" option to turn on more debugging info.
> > > Other than that, I'd be concerned about the "No such interface"
> > > printout, but I'm not to familiar with that area of the code. Maybe
> > > Theo has some advice.
> > >
> > > Cheers,
> > > Ryan
> > >
> > > --
> > > ---------------------------------------------------------------------
> > >
> > >
> > > Ryan W. Caudy
> > > <rcaudy@gmail.com>
> > > ---------------------------------------------------------------------
> > > Bloomberg L.P.
> > > <rcaudy1@bloomberg.net>
> > > ---------------------------------------------------------------------
> > > [Alumnus]
> > > <caudy@cnds.jhu.edu>
> > > Center for Networking and Distributed Systems
> > > Department of Computer Science
> > > Johns Hopkins University
> > > ---------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > wackamole-users mailing list
> > > wackamole-users@lists.backhand.org
> > > http://lists.backhand.org/mailman/listinfo/wackamole-users
> > >
> >
> > _______________________________________________
> > wackamole-users mailing list
> > wackamole-users@lists.backhand.org
> > http://lists.backhand.org/mailman/listinfo/wackamole-users
> >
>
>
> --
> ---------------------------------------------------------------------
>
>
> Ryan W. Caudy
> <rcaudy@gmail.com>
> ---------------------------------------------------------------------
> Bloomberg L.P.
> <rcaudy1@bloomberg.net>
> ---------------------------------------------------------------------
> [Alumnus]
> <caudy@cnds.jhu.edu>
> Center for Networking and Distributed Systems
> Department of Computer Science
> Johns Hopkins University
> ---------------------------------------------------------------------
>

--
---------------------------------------------------------------------
Ryan W. Caudy
<rcaudy@gmail.com>
---------------------------------------------------------------------
Bloomberg L.P.
<rcaudy1@bloomberg.net>
---------------------------------------------------------------------
[Alumnus]
<caudy@cnds.jhu.edu>
Center for Networking and Distributed Systems
Department of Computer Science
Johns Hopkins University
---------------------------------------------------------------------

_______________________________________________
wackamole-users mailing list
wackamole-users@lists.backhand.org
http://lists.backhand.org/mailman/listinfo/wackamole-users