Mailing List Archive

Hi,

On 12.04.2019 15:34, Aaron Gould wrote:
> Can I do Fusion using vMX and vQFX ? Will it work?

Leaving aside the use case and what you would actually want/could to do with it this will not work.
vQFX is basically QFX10k and QFX10k can not be used as Sat in any Fusion deployment (it can be AD in DC flavor).

So even if Fusion would be supported and/or work on vMX (which i doubt) there would be no virtual SAT to connect.
Also of course you would need a License for the AD in Fusion PE (which uses MX as AD) in order to use it.

Even MX150 (which is vMX on NFX Appliance) is not supported as AD for fusion.

--
regards
Tobias
_______________________________________________
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

Hi,

at least for Fusion Provider Edge it will not.
vMX (and MX150) are not supported.

kind regard
Rolf

> Can I do Fusion using vMX and vQFX ? Will it work?
>
>
>
>
>
> -Aaron
>

_______________________________________________
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

Ok thanks

...was purely a training/familiarization question as an attempt to spin-up some fusion in my eve-ng lab

I'll resort to my hardware, which is limited, but good gear... mx960, mx204, qfx5120.... of which I only have 1-each in my lab... but it's good nonetheless

Thanks
-Aaron

-----Original Message-----
From: Tobias Heister [mailto:lists@tobias-heister.de]
Sent: Friday, April 12, 2019 9:24 AM
To: Aaron Gould; juniper-nsp@puck.nether.net
Subject: Re: [j-nsp] Fusion using vMX and vQFX

Hi,

On 12.04.2019 15:34, Aaron Gould wrote:
> Can I do Fusion using vMX and vQFX ? Will it work?

Leaving aside the use case and what you would actually want/could to do with it this will not work.
vQFX is basically QFX10k and QFX10k can not be used as Sat in any Fusion deployment (it can be AD in DC flavor).

So even if Fusion would be supported and/or work on vMX (which i doubt) there would be no virtual SAT to connect.
Also of course you would need a License for the AD in Fusion PE (which uses MX as AD) in order to use it.

Even MX150 (which is vMX on NFX Appliance) is not supported as AD for fusion.

--
regards
Tobias

_______________________________________________
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

> Aaron Gould
> Sent: Friday, April 12, 2019 4:54 PM
>
> Ok thanks
>
> ...was purely a training/familiarization question as an attempt to spin-up
> some fusion in my eve-ng lab
>
> I'll resort to my hardware, which is limited, but good gear... mx960,
mx204,
> qfx5120.... of which I only have 1-each in my lab... but it's good
nonetheless
>
Hey Aaron,
I was thinking the same way, it would be nice to be able to lab this in a
virtual environment.
But if you think about it the fusion, it's like adding an MPC to the chassis
which in itself is I think still not supported in vMX.
So yes it would be nice to have better HW alignment with physical network
devices. (e.g. 40GE/100GE ports, etc..)

adam

_______________________________________________
juniper-nsp mailing list juniper-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp