Mailing List Archive

NI-XMR-10GX4 linecard doesn't boot.
I have NI-XMR-10GX4 linecard doesn't boot properly " CARD_STATE_SW_LOADED" after issue the command : lp boot sys mp pri 4 the unit boot into interactive mode, Then powercycle the
linecard with a power-off and power-on does not work. the rconsole 4 mode display the correct code, the diag burn-in does not detect any problem.

Does anyone have experience with this issue?

Any advice would be helpful.

Thanks


*************************************************************************************************

NetIron XMR-4000 Router#show mod
Module Status Ports Starting MAC
M1 (left ):NI-XMR-MR Management Module Active
M2 (right):
F1: NI-X-SF Switch Fabric Module Active
F2: NI-X-SF Switch Fabric Module Active
F3:
S1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3000
S2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3030
S3:
S4: NI-XMR-10Gx4 4-port 10GbE Module CARD_STATE_SW_LOADED 0 0012.f294.3090
NetIron XMR-4000 Router#
NetIron XMR-4000 Router#
NetIron XMR-4000 Router#
NetIron XMR-4000 Router#show ver
System Mode: XMR
Chassis: NetIron 4-slot (Serial #: SA03085047, Part #: 35550-000B)
NI-X-SF Switch Fabric Module 1 (Serial #: SA05081009, Part #: 35548-101A)
FE 1: Type fe200, Version 2
Switch Fabric Module 1 Up Time is 4 minutes 13 seconds
NI-X-SF Switch Fabric Module 2 (Serial #: SA05081108, Part #: 35548-101A)
FE 1: Type fe200, Version 2
Switch Fabric Module 2 Up Time is 4 minutes 13 seconds
==========================================================================
SL M1: NI-XMR-MR Management Module Active (Serial #: SA07080608, Part #: 35524-502A):
Boot : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:42:38 labeled as xmprm05600
(516258 bytes) from boot flash
Monitor : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:41:56 labeled as xmb05600
(534157 bytes) from code flash
IronWare : Version 5.6.0dT163 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Jul 24 2014 at 22:51:20 labeled as xmr05600d
(9442445 bytes) from Primary
Board ID : 00 MBRIDGE Revision : 37
916 MHz Power PC processor 7447A (version 8003/0101) 166 MHz bus
512 KB Boot Flash (AM29LV040B), 32 MB Code Flash (MT28F128J3)
2048 MB DRAM INSTALLED
--More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powered off.
2048 MB DRAM ADDRESSABLE
Active Management uptime is 4 minutes 13 seconds
==========================================================================
SL 1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082318, Part #: 35570-202A)
Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
(423373 bytes) from boot flash
Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
(539767 bytes) from code flash
IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
(7492178 bytes) from Primary
FPGA versions:
Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00

Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00

BCM5695GMAC 0
BCM5695GMAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
--More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powering on.
LP Slot 1 uptime is 3 minutes 36 seconds
==========================================================================
SL 2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082271, Part #: 35570-202A)
Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
(423373 bytes) from boot flash
Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
(539767 bytes) from code flash
IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
(7492178 bytes) from Primary
FPGA versions:
Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00

Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00

BCM5695GMAC 0
BCM5695GMAC 1
666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
LP Slot 2 uptime is 3 minutes 39 seconds
==========================================================================
All show version done

****** Rconsole **********
LP-4 Monitor>show ver
Boot 05.06.00T175 Sep 20 2013 16:43:00 PDT xmlprm05600
Monitor 05.06.00T175 Sep 20 2013 16:43:26 PDT xmlb05600 (code)
666 MHz Power PC processor MPC8541E (version 8020/0020) 333.3335 MHz bus
started=crashed
LP-4 Monitor>show flash
Boot Flash Memory : AM29LV040B
Manufacture Code : 01
Device Code : 4f
Code Flash Memory : MT28F640J3
Manufacture Code : 89
Device Code : 17
Erase Count : 0
LP-4 Monitor>show


Carlos Alfaro

Tech / Sales Support

Townsend Networks

35 Reed Blvd., Suite A Mill Valley, CA 94941

415-384-4208

mailto:carlos@townsendnetworks.com
_______________________________________________
foundry-nsp mailing list
foundry-nsp@puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp
Re: NI-XMR-10GX4 linecard doesn't boot. [ In reply to ]
Try putting the card into interactive mode and then loading the 5.6 FPGAs on it. Then power cycle the card and try booting again.

I’ve seen cards occasionally do this if their FPGA code is too far out of version sync with the boot/mon/NetIron version running.

Regards,
Mike


On Sep 5, 2014, at 5:19 PM, Carlos Alfaro <Carlos@townsendnetworks.com> wrote:

>
> I have NI-XMR-10GX4 linecard doesn't boot properly " CARD_STATE_SW_LOADED" after issue the command : lp boot sys mp pri 4 the unit boot into interactive mode, Then powercycle the
> linecard with a power-off and power-on does not work. the rconsole 4 mode display the correct code, the diag burn-in does not detect any problem.
>
> Does anyone have experience with this issue?
>
> Any advice would be helpful.
>
> Thanks
>
>
> *************************************************************************************************
>
> NetIron XMR-4000 Router#show mod
> Module Status Ports Starting MAC
> M1 (left ):NI-XMR-MR Management Module Active
> M2 (right):
> F1: NI-X-SF Switch Fabric Module Active
> F2: NI-X-SF Switch Fabric Module Active
> F3:
> S1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3000
> S2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3030
> S3:
> S4: NI-XMR-10Gx4 4-port 10GbE Module CARD_STATE_SW_LOADED 0 0012.f294.3090
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#show ver
> System Mode: XMR
> Chassis: NetIron 4-slot (Serial #: SA03085047, Part #: 35550-000B)
> NI-X-SF Switch Fabric Module 1 (Serial #: SA05081009, Part #: 35548-101A)
> FE 1: Type fe200, Version 2
> Switch Fabric Module 1 Up Time is 4 minutes 13 seconds
> NI-X-SF Switch Fabric Module 2 (Serial #: SA05081108, Part #: 35548-101A)
> FE 1: Type fe200, Version 2
> Switch Fabric Module 2 Up Time is 4 minutes 13 seconds
> ==========================================================================
> SL M1: NI-XMR-MR Management Module Active (Serial #: SA07080608, Part #: 35524-502A):
> Boot : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:42:38 labeled as xmprm05600
> (516258 bytes) from boot flash
> Monitor : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:41:56 labeled as xmb05600
> (534157 bytes) from code flash
> IronWare : Version 5.6.0dT163 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:51:20 labeled as xmr05600d
> (9442445 bytes) from Primary
> Board ID : 00 MBRIDGE Revision : 37
> 916 MHz Power PC processor 7447A (version 8003/0101) 166 MHz bus
> 512 KB Boot Flash (AM29LV040B), 32 MB Code Flash (MT28F128J3)
> 2048 MB DRAM INSTALLED
> --More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powered off.
> 2048 MB DRAM ADDRESSABLE
> Active Management uptime is 4 minutes 13 seconds
> ==========================================================================
> SL 1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082318, Part #: 35570-202A)
> Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
> (423373 bytes) from boot flash
> Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
> (539767 bytes) from code flash
> IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
> (7492178 bytes) from Primary
> FPGA versions:
> Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00
>
> Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00
>
> BCM5695GMAC 0
> BCM5695GMAC 1
> 666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
> 512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
> 1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
> --More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powering on.
> LP Slot 1 uptime is 3 minutes 36 seconds
> ==========================================================================
> SL 2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082271, Part #: 35570-202A)
> Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
> (423373 bytes) from boot flash
> Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
> (539767 bytes) from code flash
> IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
> (7492178 bytes) from Primary
> FPGA versions:
> Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00
>
> Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00
>
> BCM5695GMAC 0
> BCM5695GMAC 1
> 666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
> 512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
> 1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
> LP Slot 2 uptime is 3 minutes 39 seconds
> ==========================================================================
> All show version done
>
> ****** Rconsole **********
> LP-4 Monitor>show ver
> Boot 05.06.00T175 Sep 20 2013 16:43:00 PDT xmlprm05600
> Monitor 05.06.00T175 Sep 20 2013 16:43:26 PDT xmlb05600 (code)
> 666 MHz Power PC processor MPC8541E (version 8020/0020) 333.3335 MHz bus
> started=crashed
> LP-4 Monitor>show flash
> Boot Flash Memory : AM29LV040B
> Manufacture Code : 01
> Device Code : 4f
> Code Flash Memory : MT28F640J3
> Manufacture Code : 89
> Device Code : 17
> Erase Count : 0
> LP-4 Monitor>show
>
>
> Carlos Alfaro
>
> Tech / Sales Support
>
> Townsend Networks
>
> 35 Reed Blvd., Suite A Mill Valley, CA 94941
>
> 415-384-4208
>
> mailto:carlos@townsendnetworks.com
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp@puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp

*----------- H U R R I C A N E - E L E C T R I C ---------->>
| Mike Tindle | Senior Network Engineer | mtindle@he.net
| ASN 6939 | http://www.he.net | 510-580-4126
*--------------------------------------------------->>
Re: NI-XMR-10GX4 linecard doesn't boot. [ In reply to ]
Hi Carlo,

Just had this issue 2 weeks ago with 5.5 and 5.4. Load the card in interactive mode and load fpga , ,image, boot and monitor from tftp. After that power off/on the card and wait, you can have a look via rconsole what is going on.

Regards
Erich

> Am 06.09.2014 um 02:19 schrieb Carlos Alfaro <Carlos@townsendnetworks.com>:
>
>
> I have NI-XMR-10GX4 linecard doesn't boot properly " CARD_STATE_SW_LOADED" after issue the command : lp boot sys mp pri 4 the unit boot into interactive mode, Then powercycle the
> linecard with a power-off and power-on does not work. the rconsole 4 mode display the correct code, the diag burn-in does not detect any problem.
>
> Does anyone have experience with this issue?
>
> Any advice would be helpful.
>
> Thanks
>
>
> *************************************************************************************************
>
> NetIron XMR-4000 Router#show mod
> Module Status Ports Starting MAC
> M1 (left ):NI-XMR-MR Management Module Active
> M2 (right):
> F1: NI-X-SF Switch Fabric Module Active
> F2: NI-X-SF Switch Fabric Module Active
> F3:
> S1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3000
> S2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module CARD_STATE_UP 20 0012.f294.3030
> S3:
> S4: NI-XMR-10Gx4 4-port 10GbE Module CARD_STATE_SW_LOADED 0 0012.f294.3090
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#
> NetIron XMR-4000 Router#show ver
> System Mode: XMR
> Chassis: NetIron 4-slot (Serial #: SA03085047, Part #: 35550-000B)
> NI-X-SF Switch Fabric Module 1 (Serial #: SA05081009, Part #: 35548-101A)
> FE 1: Type fe200, Version 2
> Switch Fabric Module 1 Up Time is 4 minutes 13 seconds
> NI-X-SF Switch Fabric Module 2 (Serial #: SA05081108, Part #: 35548-101A)
> FE 1: Type fe200, Version 2
> Switch Fabric Module 2 Up Time is 4 minutes 13 seconds
> ==========================================================================
> SL M1: NI-XMR-MR Management Module Active (Serial #: SA07080608, Part #: 35524-502A):
> Boot : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:42:38 labeled as xmprm05600
> (516258 bytes) from boot flash
> Monitor : Version 5.6.0T165 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:41:56 labeled as xmb05600
> (534157 bytes) from code flash
> IronWare : Version 5.6.0dT163 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:51:20 labeled as xmr05600d
> (9442445 bytes) from Primary
> Board ID : 00 MBRIDGE Revision : 37
> 916 MHz Power PC processor 7447A (version 8003/0101) 166 MHz bus
> 512 KB Boot Flash (AM29LV040B), 32 MB Code Flash (MT28F128J3)
> 2048 MB DRAM INSTALLED
> --More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powered off.
> 2048 MB DRAM ADDRESSABLE
> Active Management uptime is 4 minutes 13 seconds
> ==========================================================================
> SL 1: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082318, Part #: 35570-202A)
> Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
> (423373 bytes) from boot flash
> Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
> (539767 bytes) from code flash
> IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
> (7492178 bytes) from Primary
> FPGA versions:
> Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00
>
> Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00
>
> BCM5695GMAC 0
> BCM5695GMAC 1
> 666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
> 512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
> 1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
> --More--, next page: Space, next line: Return key, quit: Control-cSlot 4 is powering on.
> LP Slot 1 uptime is 3 minutes 36 seconds
> ==========================================================================
> SL 2: NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module (Serial #: SA03082271, Part #: 35570-202A)
> Boot : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:00 labeled as xmlprm05600
> (423373 bytes) from boot flash
> Monitor : Version 5.6.0T175 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Sep 20 2013 at 16:43:26 labeled as xmlb05600
> (539767 bytes) from code flash
> IronWare : Version 5.6.0dT177 Copyright (c) 1996-2013 Brocade Communications Systems, Inc.
> Compiled on Jul 24 2014 at 22:57:38 labeled as xmlp05600d
> (7492178 bytes) from Primary
> FPGA versions:
> Valid PBIF Version = 4.02, Build Time = 8/26/2013 14:30:00
>
> Valid XPP Version = 1.01, Build Time = 9/6/2013 14:17:00
>
> BCM5695GMAC 0
> BCM5695GMAC 1
> 666 MHz MPC 8541 (version 8020/0020) 333 MHz bus
> 512 KB Boot Flash (AM29LV040B), 16 MB Code Flash (MT28F640J3)
> 1024 MB DRAM, 8 KB SRAM, 286331153 Bytes BRAM
> LP Slot 2 uptime is 3 minutes 39 seconds
> ==========================================================================
> All show version done
>
> ****** Rconsole **********
> LP-4 Monitor>show ver
> Boot 05.06.00T175 Sep 20 2013 16:43:00 PDT xmlprm05600
> Monitor 05.06.00T175 Sep 20 2013 16:43:26 PDT xmlb05600 (code)
> 666 MHz Power PC processor MPC8541E (version 8020/0020) 333.3335 MHz bus
> started=crashed
> LP-4 Monitor>show flash
> Boot Flash Memory : AM29LV040B
> Manufacture Code : 01
> Device Code : 4f
> Code Flash Memory : MT28F640J3
> Manufacture Code : 89
> Device Code : 17
> Erase Count : 0
> LP-4 Monitor>show
>
>
> Carlos Alfaro
>
> Tech / Sales Support
>
> Townsend Networks
>
> 35 Reed Blvd., Suite A Mill Valley, CA 94941
>
> 415-384-4208
>
> mailto:carlos@townsendnetworks.com
> _______________________________________________
> foundry-nsp mailing list
> foundry-nsp@puck.nether.net
> http://puck.nether.net/mailman/listinfo/foundry-nsp

_______________________________________________
foundry-nsp mailing list
foundry-nsp@puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp