Hi
Thanx a lot , but unfortunately i tried that too
couple of times but that too didt worked , i do not
have the cco passwd so if you dont mind request you to
copy-paste that part from the web page ,
warm regards
Prashant
--- Adeel Ahmed <adeel_373@yahoo.com> wrote:
> I think you will need to configure the following
> commands to get this working:
>
> radius-server vsa send accounting
>
> radius-server vsa send authentication
>
>
> Take a look at the following example for reference:
>
>
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a00800b5de5.html
>
> Eventhough the example is not from a uBR7246 you can
> see the NAS(AS5300) sending radius attribute 31 to
> the
> radius-server.
>
> Hope this helps !
>
> Adeel.
>
> --- Nilesh Naik <qmailindia@yahoo.com> wrote:
> > Hi all
> >
> > we rae using cisco uBR 7246, as our PPPoE
> > concentrator and NAS , we are running IOS (tm)
> 7200
> > Software (UBR7200-IK8S-M), Version 12.2(11)BC3,
> > EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc2) on this uBR ,
> >
> > we are presently using the Radius
> Authentication
> > for all the PPPoE dialin Users , but when i see in
> > the
> > debug mode by enabling "debug radius", debug aaa
> > authentication" & "debug aaa accounting" i cant
> see
> > cisco uBR sending "Calling-Station-Id" attribute
> to
> > the radius , which i think sould contain value of
> > the
> > customer's MAC Address if i am correct ?? pls
> > correct
> > me if i am wrong here ?
> >
> > now i check out every option on the Ubr to
> enable
> > this i even tried these following commands
> >
> > aaa group server radius accountgroup
> > server 20.17.92.2 auth-port 1645 acct-port 1646
> > server 20.17.92.1 auth-port 1645 acct-port 1646
> > authorization accept default ( added this
> command)
> > !
> > then
> > radius-server attribute list default
> >
> > and also added "calling-station-ID" attribute
> under
> > attribute list (Default the one created by above
> > command)
> >
> >
> > than also i cant see cisco uBR our NAS sending the
> > Calling-Station-ID to the radius server ,
> >
> > i even tried doing this
> >
> > my-cmts02(config)#radius-server attribute ?
> > 11 Filter-Id attribute configuration
> > 188 Num-In-Multilink attribute
> configuration
> > 218 Address-Pool attribute
> > 32 NAS-Identifier attribute
> > 4 NAS IP address attribute
> > 44 Acct-Session-Id attribute
> > 6 Service-Type attribute
> > 69 Tunnel-Password attribute
> > 8 Framed IP address attribute
> > list List of Attribute Types
> > nas-port NAS-Port attribute configuration
> >
> >
> > but as u see there isnt any thing mentioned for
> > "calling-station-ID" (31) so i was not able to
> > enable
> > it ,
> >
> >
> > so if any one knows anything about this then
> > kindly
> > let me know what i am missing here ? what should i
> > do
> > to enable it so that it starts sending
> > calling-station-ID attribute?
> >
> > regards
> > Prashant
> >
> > __________________________________
> > Do you Yahoo!?
> > The New Yahoo! Search - Faster. Easier. Bingo.
> > http://search.yahoo.com
> > _______________________________________________
> > cisco-ubr mailing list
> > cisco-ubr@puck.nether.net
> > http://puck.nether.net/mailman/listinfo/cisco-ubr
>
>
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Search - Faster. Easier. Bingo.
> http://search.yahoo.com
__________________________________
Do you Yahoo!?
The New Yahoo! Search - Faster. Easier. Bingo.
http://search.yahoo.com
Thanx a lot , but unfortunately i tried that too
couple of times but that too didt worked , i do not
have the cco passwd so if you dont mind request you to
copy-paste that part from the web page ,
warm regards
Prashant
--- Adeel Ahmed <adeel_373@yahoo.com> wrote:
> I think you will need to configure the following
> commands to get this working:
>
> radius-server vsa send accounting
>
> radius-server vsa send authentication
>
>
> Take a look at the following example for reference:
>
>
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a00800b5de5.html
>
> Eventhough the example is not from a uBR7246 you can
> see the NAS(AS5300) sending radius attribute 31 to
> the
> radius-server.
>
> Hope this helps !
>
> Adeel.
>
> --- Nilesh Naik <qmailindia@yahoo.com> wrote:
> > Hi all
> >
> > we rae using cisco uBR 7246, as our PPPoE
> > concentrator and NAS , we are running IOS (tm)
> 7200
> > Software (UBR7200-IK8S-M), Version 12.2(11)BC3,
> > EARLY
> > DEPLOYMENT RELEASE SOFTWARE (fc2) on this uBR ,
> >
> > we are presently using the Radius
> Authentication
> > for all the PPPoE dialin Users , but when i see in
> > the
> > debug mode by enabling "debug radius", debug aaa
> > authentication" & "debug aaa accounting" i cant
> see
> > cisco uBR sending "Calling-Station-Id" attribute
> to
> > the radius , which i think sould contain value of
> > the
> > customer's MAC Address if i am correct ?? pls
> > correct
> > me if i am wrong here ?
> >
> > now i check out every option on the Ubr to
> enable
> > this i even tried these following commands
> >
> > aaa group server radius accountgroup
> > server 20.17.92.2 auth-port 1645 acct-port 1646
> > server 20.17.92.1 auth-port 1645 acct-port 1646
> > authorization accept default ( added this
> command)
> > !
> > then
> > radius-server attribute list default
> >
> > and also added "calling-station-ID" attribute
> under
> > attribute list (Default the one created by above
> > command)
> >
> >
> > than also i cant see cisco uBR our NAS sending the
> > Calling-Station-ID to the radius server ,
> >
> > i even tried doing this
> >
> > my-cmts02(config)#radius-server attribute ?
> > 11 Filter-Id attribute configuration
> > 188 Num-In-Multilink attribute
> configuration
> > 218 Address-Pool attribute
> > 32 NAS-Identifier attribute
> > 4 NAS IP address attribute
> > 44 Acct-Session-Id attribute
> > 6 Service-Type attribute
> > 69 Tunnel-Password attribute
> > 8 Framed IP address attribute
> > list List of Attribute Types
> > nas-port NAS-Port attribute configuration
> >
> >
> > but as u see there isnt any thing mentioned for
> > "calling-station-ID" (31) so i was not able to
> > enable
> > it ,
> >
> >
> > so if any one knows anything about this then
> > kindly
> > let me know what i am missing here ? what should i
> > do
> > to enable it so that it starts sending
> > calling-station-ID attribute?
> >
> > regards
> > Prashant
> >
> > __________________________________
> > Do you Yahoo!?
> > The New Yahoo! Search - Faster. Easier. Bingo.
> > http://search.yahoo.com
> > _______________________________________________
> > cisco-ubr mailing list
> > cisco-ubr@puck.nether.net
> > http://puck.nether.net/mailman/listinfo/cisco-ubr
>
>
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Search - Faster. Easier. Bingo.
> http://search.yahoo.com
__________________________________
Do you Yahoo!?
The New Yahoo! Search - Faster. Easier. Bingo.
http://search.yahoo.com